Your stereo receiver is going into protection mode because the receiver has an internal short, a speaker is bad or the speaker wiring has a problem, such as incorrect wire gauge or bad connections. If the receiver shuts off after connecting a speaker, that speaker’s wiring or the speaker itself has a problem.
Turn off the receiver and let it cool for a few hours; then try again. If the protection mode warning doesn’t go away on its own, press the reset button. If that doesn’t work, disconnect the power lead from your receiver for 30 seconds and then reconnect it. If it still doesn’t work, it’s time to take it to the dealer.
Thereof, How do I get my Sony stereo out of Protect Mode?
To reset the internal surge protection circuit unplug the AC power cord from the wall for at least 30 minutes. Ensure the top of the home audio device has proper ventilation to keep it from overheating. Running the home audio device in a poorly ventilated cabinet can trigger the protection circuit.
Also to know is, How do I get my Sony home theater out of protected mode? To reset the internal surge protection circuit unplug the AC power cord from the wall for at least 30 minutes. Ensure the top of the home audio device has proper ventilation to keep it from overheating. Running the home audio device in a poorly ventilated cabinet can trigger the protection circuit.
Subsequently, question is, How do you reset a Sony receiver? – Press the POWER button to power off the receiver.
– Press and hold down the POWER button.
– Wait approximately 5 seconds and then release the POWER button.
Also, How do I fix the Sony push power protector?
– Turn off the home audio device, and remove all speaker wires from the back. Then turn the device back on and check if the issue is resolved.
– Inspect the speaker cords.
– Make sure the speaker impedance is within the recommended range.
What does it mean when it says push power protector?
PUSH POWER / PROTECT / PROTECTOR is flashing in the display of the home audio device. … If there has been an electrical surge or power outage, then the internal surge protection inside the home audio device may have been triggered to protect the device from the surge. This is normal.
Why does my stereo go into protect mode?
Your stereo receiver is going into protection mode because the receiver has an internal short, a speaker is bad or the speaker wiring has a problem, such as incorrect wire gauge or bad connections. … If the receiver shuts off after connecting a speaker, that speaker’s wiring or the speaker itself has a problem.
What does it mean when my Sony receiver says protect?
The Protector error on Sony amplifiers and home theater receivers means there is an internal speaker issue or connection issue that may soon damage the receiver.
How do I reset my Sony DVD at home theater?
– On the supplied remote, press the HOME button.
– Use the left or right arrow buttons to select Settings.
– Use the up or down arrow buttons to select Resetting, then press. (Enter).
– Select Reset to Factory Default Settings and follow the on-screen instructions.
How do I fix my Sony receiver?
Why does it say protect on my Sony stereo?
The Protector error on Sony amplifiers and home theater receivers means there is an internal speaker issue or connection issue that may soon damage the receiver. To protect its components, the receiver automatically goes into protect or protector mode, flashing the error in the receiver’s display.
How do I reset my Sony surround sound without a remote?
– Unplug the power cord from the electrical wall outlet.
– Plug the power cord back into the electrical wall outlet.
– Press the power button. to turn on the stereo system.
– Press and hold the STOP button. and EQ button at the same time until RESET or RESET OK appears on the display panel.
How do I reset my Sony surround sound system?
– On the supplied remote, press the HOME button.
– Use the left or right arrow buttons to select Settings.
– Use the up or down arrow buttons to select Resetting, then press. (Enter).
– Select Reset to Factory Default Settings and follow the on-screen instructions.
What is a power protector?
Power strips and surge protectors, also called surge suppressors, are different. Typically, power strips are cheap, multi-outlet products that are merely an expansion of a wall outlet. These usually have a circuit breaker (on/off switch) of some sort, but most don’t offer any real “protection” from electrical issues.
How do you reset a Sony DVD player?
– On the supplied remote control, press the HOME button.
– Select Setup.
– Select Resetting or icon.
– Select Reset to Factory Defaults Settings.
– Select All Settings.
– Select Start.
– Select Close.
– Turn off your device, then turn it back on.
Do I really need a surge protector?
Without a surge protector, a power spike or power surge could shorten the life of your computer, wipe out all of your data, or even completely destroy your system. In fact, you should use a surge protector with any high-end electronic device.
How do you reset a DVD player?
Ensure no discs are playing in the DVD player. On the DVD remote control, press the UP ARROW or DOWN ARROW button to select the SETUP icon. Press the ENTER button. Press the UP ARROW or DOWN ARROW button to select RESET .
Don’t forget to share this post 
References and Further Readings :
