Under normal conditions the pressure switch doesn’t cycle the compressor. … In your case, if your system is working properly, you should be able to bypass the switch temporarily until you can replace it.
The low pressure switch monitors the refrigeration system for a loss of refrigerant charge, and may also be helpful in stopping the evaporator (indoor) coil from freezing up due to a dirty filter or low airflow over the coil.
Thereof, What are the symptoms of a bad AC pressure switch?
– AC system cutting on and off rapidly. Repeatedly cycling on and off is part of the normal operation of an AC system. …
– Unable to cool the car. If either of the AC pressure switches fails, then the system will have a difficult time maintaining the pressure required to function properly. …
– Compressor not coming on.
Also to know is, What does an AC pressure switch do? The AC pressure switch is a safety switch mounted on the upper and lower sides of the air conditioning system. When the pressure goes up too high or falls too low (on the side of the system where the sensor is mounted), the switch turns off the compressor to avoid damage.
Subsequently, question is, Where is the AC low pressure switch located? The low side service valve is located in the line that runs from the compressor through the evaporator (firewall) and up to the condensor on the low pressure (suction) side of the system.
Also, What does a AC low pressure switch do?
The low pressure switch monitors the refrigeration system for a loss of refrigerant charge, and may also be helpful in stopping the evaporator (indoor) coil from freezing up due to a dirty filter or low airflow over the coil.
How do you replace a low pressure switch on an air conditioner?
– Step 1: Locate the A/C pressure switch. …
– Step 1: Disconnect the negative battery cable. …
– Step 2: Remove the switch electrical connector.
– Step 3: Remove the switch. …
– Step 1: Install the new switch. …
– Step 2: Reinstall the electrical connector.
– Step 3: Reinstall the negative battery cable. …
– Step 4: Test the A/C.
How do you test a low pressure switch on an air conditioner?
How do you fix a low pressure switch?
How do you bypass a 3 wire AC pressure switch?
– Step 1: Reset Power-train Control Module (PCM) Fuse. The first simple technique is getting rid of the PCM fuse. …
– Step 2: Jump AC Relay. …
– Step 3: Connect The Charging Connectors. …
– Step 4: Open Gas Valves.
How do I fix my AC pressure switch?
– Step 1: Locate the A/C pressure switch. …
– Step 1: Disconnect the negative battery cable. …
– Step 2: Remove the switch electrical connector.
– Step 3: Remove the switch. …
– Step 1: Install the new switch. …
– Step 2: Reinstall the electrical connector.
– Step 3: Reinstall the negative battery cable. …
– Step 4: Test the A/C.
Where is the AC high pressure switch located?
The location of the refrigerant pressure sensor can differ a lot between car models and depending on whether you are going to replace the high or low-pressure sensor. But usually, the sensors are most often located in the engine bay or under the front/on the AC condenser on the front of the car.
How do I test my AC low pressure switch?
Check the pressure of the air conditioning system by attaching a low pressure gauge from a refrigerant recharge kit to the low pressure fitting, located between the accumulator and the compressor and marked with a capital “L.” According to AA1 Car, on an 80 degree day, the low pressure gauge should measure 56 psi ( …
How does a low pressure switch work?
A low-pressure switch is connected to the suction, or “low” side of the system to sense suction pressure. When the pressure in the system exceeds the high pressure switch setting, the switch will open circuit the compressor clutch and the compressor will stop circulating refrigerant.
What causes low pressure switch trip?
Things that can cause the low-pressure switch to trip include: Low refrigerant charge because of a refrigerant leak. Blower motor failure in the air handler. Plugged evaporator coils or a blockage of air flow.
How do you jump a low pressure switch on an air conditioner?
Unplug the plug on the low pressure switch. Use a stiff piece wire bent in a U shape to jump the plug (should be just two wires) stick your jumper wire in the plug. Even a paper clip will work. If your AC compressor kicks on, then you know the system is working.
How do you bypass the pressure switch on an air compressor?
How do I test my AC pressure switch?
Don’t forget to share this post 
References and Further Readings :
