The Installer Code on a panel is used for entering installer programming mode. In this mode, various changes to the function of the system can be made. … This menu allows users to add and program new devices, change system settings, and change delay times.
The default installer code for a DSC is 5555. The installer code is the code that is used to get into the DSC programming mode so you can set the system up and make changes to panel programming. Having the installer code is the most important part of setting up the system.
Thereof, What is the default installer code for DSC?
5555
Also to know is, How do you program zones on a DSC 1832? – Enter programming. …
– Enter the appropriate section for the zone(s) you’re programming. …
– Once in that programming section each zone, in order, will have a 2-digit zone definition.
Subsequently, question is, How do I factory reset my DSC panel? – Power down the system completely.
– Connect a short (wire) between Zone 1 and PGM1 on the control panel (remove all other wires form these terminals).
– Power up the control panel (AC power only) for 10 full seconds.
– Power down the control panel, remove short between Zone 1 and PGM1.
– Power up the control panel.
Also, How do I default a DSC Neo panel?
How do you bypass DSC?
– The System Must be disarmed prior to proceeding.
– Press the * Key.
– Press the 1 Key.
– Use the > key to scroll to the zone you wish to bypass.
– Press the * Key on the appropriate zone.
– A “B” should appear next to the zone when the system is bypassed.
What is the installer code for ADT?
You can always try the default Installer Code first but it would be unusual for a security dealer to not change the code as part of their installation procedure. If you have an ADT SafeWatch which is a rebranded Honeywell Vista control, the default Installer Code is 6321.
How do I set a default DSC panel?
– Prepare the terminals. If there are any wires connected to the Z1 and PGM1 terminals, remove them and mark them appropriately. …
– Power panel down. …
– Short across terminals. …
– Apply AC power. …
– Remove AC power. …
– Remove the jumper. …
– Restore power.
How do I turn off my alarm without the code?
You can turn off or power down your home alarm system by disconnecting its backup battery and then unplugging the transformer for the device from the wall outlet. You can confirm that the panel has been powered down by checking its touchscreen or keypad and making sure that it is blank.
How do I mute my DSC keypad?
– Press * and then the 6 button on the keypad.
– Enter your master Code.
– Use the < and > keys to scroll to “Buzzer Control”
– Press *
– Use the < and > keys to scroll through the various buzzer settings, and adjust to your preference. “0” will silence the DSC keypad.
– Press # to exit.
How do I turn off my Honeywell alarm without the code?
You can turn off your Honeywell Alarm System by disconnecting both of its power supplies. These include its backup battery and its plug-in transformer. You should disconnect the backup battery before unplugging the transformer. Once both are disconnected, the panel will shut down.
How do you program a DSC keypad?
How do I bypass the alarm code?
– Enter the following: Your 4-digit code. The number 6 (bypass button) Two-digit zone number of the zone you want to bypass. (01, 02, 03, etc.)
– Repeat this process for all zones you would like to bypass.
– Once your system is disarmed, this process will need to be repeated in order to arm your system again.
How do I disable DSC?
– Disarm from the panel. To disarm from the panel, simply enter in a valid user code or the Master Code. …
– Disarm with a key fob. To disarm using a key fob simply press and hold the disarm button on a programmed key fob while within range of the system. …
– Disarm through Alarm.com.
How do you disarm a house alarm without the code?
You can turn off or power down your home alarm system by disconnecting its backup battery and then unplugging the transformer for the device from the wall outlet. You can confirm that the panel has been powered down by checking its touchscreen or keypad and making sure that it is blank.
How do I find my ADT installer code?
How do I know my DSC model?
The control panel, which is a metal cabinet, will be mounted out of the way in a utility closet or in the basement. The metal cabinet contains the system electronics, fuses and back up battery. Some alarm systems have two names, the Model Number and the Marketing Name.
Don’t forget to share this post 
References and Further Readings :