How to Reset a Kenmore Elite HE Washer
- Press the “Stop” button twice, and then press the “Power” button.
- Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
- Press the “Start” button to complete the reset process and restart the washing machine.
Likewise, How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Also, How do I fix the f11 code on my Kenmore washer?
To clear and restart the control follow the these steps: Unplug or turn the circuit breaker off for 10-20 minutes. Reconnect the unit to the power source by turning the breaker back on or plugging the washer back in. Press the Pause/Cancel/Stop button twice to clear the display.
Moreover, How do I troubleshoot my Kenmore washer?
Kenmore Washer Troubleshooting
- Bad lid switch. If your washing machine does not stop every time you open the lid, your lid switch is bad. …
- Clogged waste hose. If your washing machine does not drain the waste water, the waste hose might be clogged. …
- Bad drain pump. …
- Bad pump motor. …
- Broken drive belt. …
- Bad tub motor.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
How do I reset my Kenmore front load washer?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
What is F11 error code?
The F11 error code in the Whirlpool washer reports about the engine control board malfunction. … Communication errors between components in the Whirlpool washer occur quite rarely. But this appliance is all about water, moisture, and spin at high speed.
How do I fix F11 error?
It means when a key on the keypad has been detected as pressed in for a long time the F11 error is reported and all oven commands are terminated. First simply press the cancel key to clear the code. The error may have been caused by just holding down a key too long by mistake.
What does error code F11 mean?
Resolution: Error code F11 = Serial Communication Error. Error codes can be caused by a Power Surge or other electrical anomaly,attempt to return the washer to operation by following the Hard Reset procedure below. In some cases the control can be non-functioning or may not accept activation from the control panel.
How do you fix a Kenmore washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
Why won’t my Kenmore washer wash?
If the Kenmore washer gets stuck on the wash cycle, a temporary fix would be to manually spin the basket. This issue is likely the result of a faulty timer, water line valve, or lid switch. Meanwhile, check the line fuse or user control and display board if the washer won’t start the wash cycle.
What would cause a Kenmore washer not to drain?
If the washer won’t drain water the drain pump might be defective. It’s also common for a small sock or other article of clothing to get caught in the drain pump or in the drain hose. Check both for an obstruction before replacing the pump. If the washer won’t drain there might be a clogged pump or hose.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
Why is washer not draining water?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I fix the error on my Kenmore Elite washer?
Kenmore front-load washer LE error code
- Overloaded washer. Make sure the washer isn’t overloaded. …
- Too much detergent. If you see lots of suds in the tub, let the washer sit idle for 30 minutes so the foam dissipates. …
- Drive system obstruction. …
- Loose wiring or defective drive motor.
How do you run a diagnostic on a Kenmore front-load washer?
Select “Drain/Spin” or “No Spin” by pressing the SPIN SPEED button. Within 5 seconds, push the “Prewash” option four times. The diagnostic should begin when C:00 light up.
What does F11 mean on a Kenmore oven?
F11. indicates a failure with a. shorted keypad. Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up, replace EOC (Electronic Oven Control).
What does F1 mean on a LG stove?
LG F1 – Touchpad fault indicating a stuck button or bad connection between touchpad and oven control.
What does F1 mean on Whirlpool washer?
When the Whirlpool Cabrio displays an F1 error, this means the the control board is having difficulty communicating with the motor. To fix your F1 error, you can first try to unplug your washing machine for 15 minutes and then plug it back in. If this doesn’t work, you will need to replace the control board.
Why is my Kenmore stove beeping F1?
The F1 error means that there is an electronics failure within the oven. This failure can occur within the keypad itself, the electronic oven control or the oven temperature sensor. The error can also indicate data corruption within the oven’s electronic controller.
Why does my oven beep and say F10?
F10 is a common error code for several manufacturers that appears when your oven exceeds the temperature you set it at in either the cook cycle or the clean cycle. … A defective temperature sensor can also cause this problem.
What is F10 code on Kenmore oven?
The F10 code on a Kenmore oven means that the oven is overheating — the oven is detecting a temperature far over the safe range of operation. Most models also start beeping when this happens since it can be a safety concern.
