The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
Table of Contents
READ ALSO
Likewise, How do I fix the LF on my washing machine?
LF in the display
Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.
Also, What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
Moreover, What does F5 and E3 mean on a washing machine?
The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
How do I fix the F5 on my Kenmore washer?
It goes through the wash cycle and then ends with an F5 error and recurring beeping alarm. The “lid locked” LED flashes as well. The only way to clear the codes is to unplug and let sit, and then plug back in. Then it is good to go again.
How do I fix E1 error on my washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
What does FL Lo mean on a washer?
The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive.
Where is the water inlet valve located on a washing machine?
The inlet valve can be found on the back of your washing machine. Its principal responsibility is to manage the entry of water into your washing machine. In other words, the inlet valve acts as a sort of gate keeper, allowing water to flow into the tub when it receives certain electrical signals from the washer.
How do I fix error code E3?
This could be due to a wiring mistake, faulty fan assembly, faulty fan motor, or a faulty control board. Before touching or maneuvering the wires, be sure to turn off the power from the disconnect box for the outdoor unit, or from the breaker box for the indoor unit.
How do I fix E3 error on my washing machine?
0C, 0E, E3 code appears on the washer screen. In this case, you need to drain water and remove the laundry. Then, run the rinse mode to clean the drum. Next, start the technique to make sure that the OC error has disappeared.
What does E3 mean on AC?
E3 error code indicates a indoor fan speed malfunctioning which can be affiliated to a bad indoor circuit board or a bad indoor fan motor.
What does E3 mean on my washing machine?
The E3 error in Samsung washers means a drum overflow with water. The water level sensor sends a signal indicating that there is too much water in the drum. … The E3 error code indicates overfilling with water. That’s what this error, displayed on the washing machine, means.
How do I fix E3 error on my washing machine?
5 Answers
- Unplug The Washing Machine: Unplug the washer for 2-3 minutes. …
- Check Wire Connections On Drive Motor: One fairly common issue that causes the 3E error code is connection problems. …
- Check Wire Connections On Control Board: …
- Check Hall Sensor:
What does F5 and E2 mean on a washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
How do I fix the code on my Kenmore washer?
Kenmore front-load washer LE error code
- Overloaded washer. Make sure the washer isn’t overloaded. …
- Too much detergent. If you see lots of suds in the tub, let the washer sit idle for 30 minutes so the foam dissipates. …
- Drive system obstruction. …
- Loose wiring or defective drive motor.
How do you reset a Kenmore washing machine?
How to Reset a Kenmore Elite HE Washer
- Press the “Stop” button twice, and then press the “Power” button.
- Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
- Press the “Start” button to complete the reset process and restart the washing machine.
Why is my washing machine showing E1?
When the Washing Machine is displaying E1 in the panel, it is indicating an error in the water supply. The appliance is not detecting that the unit is filling with water.
How do I clear E1 F9 code?
Filter clogged
It picks up trash and small objects before they reach the pump, instigating error code E1 F9. To access the filter, unscrew and remove the front panel. Then gently turn it and remove it from the groove.
What does E1 mean?
| Acronym | Definition |
|---|---|
| E1 | Everyone |
| E1 | Enterprise One (JD Edwards software) |
| E1 | Echelon 1 (US DoD) |
| E1 | European Basic Multiplex Rate (30 voice channels; 2.048 Mbps) |
How do you reset the code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you clear the LF code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
What does code LF mean on Kenmore washer?
LF. Error code: LF. stands for long fill and occurs when the water level does not change for a period of time after the valves are turned on. All washers are designed to operate with a water supply pressure of 20-100 PSI.
How do I know if my inlet valve is bad?
Signs that point to an inlet valve problem include leaks that fill the dishwasher when not running, the dishwasher filling too slowly when in use, or the dishwasher not filling at all. Leaks that end up outside of the dishwasher also can indicate an inlet valve problem, and this must be addressed immediately.
Why is there no water going into my washing machine?
So a lack of water at the wash or rinse cycle could be a result of a broken water inlet valve. … Perhaps there is no voltage coming into the valve, which means the electrical process is being halted somewhere else in the machine, like the water level switch, the timer, the lid switch or the cycle selector switch.
