If you cannot change channels on your Samsung smart TV, first double-check to ensure your Samsung remote is programmed with your cable box. If afterward, you have confirmed your remote and cable box are connected, you will need to reset your remote.
Table of Contents
READ ALSO
Likewise, How do I fix an unresponsive remote?
NOTE: Because each of these steps represents a possible solution, check the function of the remote control after completing each step.
- Make sure none of the remote buttons are jammed.
- Reset the remote. …
- Clean the remote control terminals. …
- Replace with fresh batteries. …
- Perform a power reset on the TV.
Also, Why won’t my remote let me change channels?
Check the batteries in your remote control. If you do not see at least 1 button lighting up on the remote upon pressing the button, then the batteries may be depleted. Change the batteries in your remote control and retest. Power down your set-top box using the “CBL” button on the remote and then power it back up.
Moreover, Why does TV remote not change channels?
Remote will not change channels or turn on the TV. Batteries are low, dead, or inserted incorrectly. Verify the batteries are inserted in the correct direction. … If the box turns ON or OFF, then install new batteries in the remote and try again.
How do you sync a Samsung remote?
On most Samsung TVs, the remote control sensor is located on the lower right hand side of the TV. If not, it is directly in the bottom center. Next, press and hold the Return and Play/Pause buttons simultaneously for at least 3 seconds. Your TV will begin syncing with the Smart Remote.
Why is my remote not working?
1 Check the Batteries of the Supplied Remote
Low battery power can cause the remote to intermittently function, or not function at all. … Replace the back cover on the remote, and slide down to click it into place. If the remote fails to respond properly after this, replace the existing set of batteries with new ones.
What do you do if your TV remote stops working?
Section B: Checking items of the remote control (common)
- Make sure none of the remote buttons are jammed.
- Reset the remote. …
- Clean the remote control terminals. …
- Replace with fresh batteries. …
- Perform a power reset on the TV. …
- For Android TV/Google TV: symptoms may improve by updating the software of the remote control.
How do I get my remote to change channels?
Remote control won’t change TV channels
- Make sure there are no obstacles between the remote and your TV.
- Move closer to the TV and make sure the remote is pointed directly at the TV’s front panel.
- Make sure the batteries are installed correctly.
- Try fresh batteries.
How do I fix my directv remote that won’t change channels?
If that didn’t help, try resetting the remote to its default factory settings:
- Press and hold MUTE and SELECT together until the light flashes three times.
- Press 9, 8, 1 and SELECT. The remote flashes four times and should now reset.
How do I get my directv remote to change channels?
Make sure your remote is paired with your receiver.
- Point the remote at your Genie, Genie Mini, or Wireless Genie Mini.
- Press and hold MUTE and ENTER at the same time on your remote.
- The screen displays Applying IR/RF Setup. The remote is synced.
How do I fix my TV remote sensor not working?
Follow the steps below to troubleshoot this issue:
- Make sure the remote control is set properly to control the TV. …
- Make sure there is nothing in front of the infrared (IR) sensor on the TV that may be blocking the signal from the remote control.
- Make sure you are pointing the remote control towards the IR sensor.
How do I turn my Samsung TV on without the remote?
When facing the TV, certain models have the TV Controller on back of the TV in the bottom right corner. The control stick toggles up and down as well as side to side – the menu options will appear on the TV screen when you press the center button. Long press the center button to turn the TV on or off.
Why does my Samsung remote say not available?
If your Samsung remote keeps saying that it is not available, turn your television set off and allow it to completely drain of power. Once this is completed, turn the TV back on and simultaneously hold down the ‘Return’ and ‘Play/Pause’ button on the remote control as the TV starts back up.
How do I get my remote to work on my TV?
Turn on your TV or another device you wish to control. Press and hold the corresponding DEVICE and POWER buttons on the remote at the same time. Wait until the power button comes on and then release both buttons. Pointing the remote at the TV or another device, press the Power button on the remote and wait 2 seconds.
Why will my remote not change channels?
Remote will not change channels or turn on the TV. Batteries are low, dead, or inserted incorrectly. Verify the batteries are inserted in the correct direction. … If the box turns ON or OFF, then install new batteries in the remote and try again.
How do I get my TV remote to work?
TV remote controls work in a similar way but using a type of light called infrared (or IR for short). The remote control has an LED light in it which flashes really quickly to emit a message which is then picked up by the TV. The remote is called the transmitter, and the TV is called the receiver.
How do I reset my cable remote?
To perform a factory reset:
- Press the Setup button until the LED at the top of the remote changes from red to green.
- Press 9-8-1.
- The LED will blink green twice to indicate that the remote was reset.
How do I resync my DirecTV remote to my TV?
Press Menu. Select Settings & Help > Settings > Remote Control > Program Remote. Select the device you want to pair and follow the on-screen instructions to complete the process. Your remote should now be paired and ready to go!
How do you fix a stuck TV on one channel?
Unplug the screw on coax cord from the TV, and it should stop power cycling. Once it has stopped, while the coax cord is disconnected, run the channel scan to erase the previous channel listing. Once that scan completes, reattach the coax cord, and rerun the channel scan to find the current frequencies.
How do I sync my DirecTV Genie remote to my TV?
Point the remote at your Genie HD DVR, Genie Mini, or Wireless Genie Mini. Press and hold the MUTE and ENTER buttons. Stop when the green light at the top of the remote blinks twice. When the TV screen displays Applying IR/RF setup, you are in RF mode and ready to program the remote.
Can I use my DirecTV remote as a universal remote?
One of the problems that people who have DirecTV run into is that after their DirecTV dish and box are installed, they receive a new DirecTV remote control that is not preset to control their television. However, DirecTV remotes are universal remote controls, which means that you can program them to work with any TV.
How do I know if my remote control sensor is working?
Look at the viewfinder or screen of your camera/camcorder or mobile phone. If the remote control sends a signal, you should see a light in the viewfinder or screen of your camera/camcorder or mobile phone when you press a button on the remote control.
How do I know if my remote sensor is working?
To check if your IR Remote is sending a signal, follow the steps below:
- Pick a device to use: Digital Camera – turn the camera on. …
- Point the end of the remote control with the IR emitter at the camera or camcorder lens.
- Look at the viewfinder or LCD screen.
- Press and hold one of the buttons on the remote control.
