What is an F21 or F02 Error Code on my Maytag Front Load Washer? These error codes indicate that drain times are longer than expected.
Table of Contents
READ ALSO
Likewise, What does the Code F mean on a Whirlpool washer?
The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won’t run at all.
Also, Can you reset a Maytag washer?
In addition to a number of heat and tumbling settings, many Maytag washers also have digital displays that indicate the minutes left on a washing cycle, which settings you have chosen and error messages. … You also can reset the washer if you want to cancel a setting you chose.
Moreover, What does F mean on my Maytag washer?
Maytag F/02 – Drain Cycle Too Long
The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. … If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
Why is my Maytag washer not working?
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.
Why does my washer keep saying F?
The F indicates that the washer control detected a component problem. … If the F code was caused by excessive suds preventing the washer from draining, you may be able to shut the door and run a drain/spin cycle to remove the water from the washer.
Why is my washing machine showing F?
If your LG appliance stops during operating and displays the PF error code, it is a signal about unstable voltage in the network. And the error can appear in any wash mode.
What does F code mean?
FCODE
| Acronym | Definition |
|---|---|
| FCODE | Forth Code (electrical engineering) |
How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I reset my front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load Washer
| Error Code | Error |
|---|---|
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
| F8 E1 or LO FL | The washer is sensing a low flow of water. |
• 15 juin 2020
What does FH error code mean?
FH Error Code
FH indicates that there is a Water Inlet Problem—no or insufficient water supply. Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
How do I fix F5 on Maytag washer?
The F5 E2 alert indicates the washer can‘t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
Does a washing machine have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How dO you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How dO I reset my Whirlpool front load washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
What are the problems with washing machine?
7 Common problems with washing machine
- Washing machine not starting. …
- Washing machine is noisy. …
- Excessive vibrations during operation. …
- Washing machine making noise when draining or not draining at all. …
- Washing machine over-filling or under-filling. …
- Washing machine not spinning. …
- Water leaking from soap drawer.
How can I fix my washing machine?
It’s an easy and inexpensive fix, about $22.
- Fix 2: Draining problems. Replace the pump. Tip the machine back and support it with blocks. …
- Fix 3: Slow fill or no fill. Replace the water valve. Remove the water valve bracket and mount the new valve. …
- Fix 4: Won’t agitate or spin. Replace the lid switch.
What does Code F 28 mean on a Whirlpool washer?
Posted: 08/01/17. shantapanchu a F28 error code is a common problem indicating that there is a communication problem with the central control unit. Any error code can be caused by a electrical anomaly. try to reset your washer.
Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I manually drain my Whirlpool washer?
Find the “Pause/Cancel” button on the control panel. Press this button twice to drain the washer. Press the “Power” button and rotate the cycle selection knob to “Drain and Spin” to remove the remaining water from the load. Check the washer’s discharge hose if the water fails to drain from the washtub.
