Whirlpool Tumble Dryer Reset Procedure
- Turn on the tumble dryer main power.
- Within 10 seconds turn the program selector from off to teh 6 o’clock postion, pointing straight down.
- Push the “Start” button three times.
- Turn the program selector to the “one” position which should be the CW or airing program.
Likewise, What would cause a whirlpool dryer not to start?
Sometimes a Whirlpool dryer not starting is more of a power issue than a dryer malfunction. … Make sure the dryer is correctly plugged into the proper electrical outlet. Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses.
Also, How do I reset a Whirlpool Duet dryer?
How do I reset my Whirlpool Duet steam dryer?
- Inspect household fuses or breakers.
- Close the dryer door firmly.
- Press and hold the “Start” button for five seconds.
- Check the display on the dryer for error codes.
- Press the “Start” button and hold for several seconds to restart the dryer if “PF” appears on the display.
Moreover, What would cause a clothes dryer not to start?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … If it doesn’t turn on, it’s likely that the dryer has no power. Check your power cord and the house circuit breaker.
Does unplugging a dryer reset it?
Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.
How do I know if the thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
When I push the start button on my dryer nothing happens?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … If it doesn’t turn on, it’s likely that the dryer has no power. Check your power cord and the house circuit breaker.
Is there a fuse on a Whirlpool dryer?
Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.
How do you troubleshoot a Whirlpool Duet dryer?
How to Troubleshoot a Whirlpool Duet Electric Dryer
- Inspect household fuses or breakers. …
- Close the dryer door firmly. …
- Press and hold the “Start” button for five seconds. …
- Check the display on the dryer for error codes.
How do I fix the control lock on my Whirlpool Duet dryer?
How to Unlock the Controls for a Whirlpool Duet Washer
- Locate the “Control Lock/Unlock” button on your Duet’s control panel.
- Press and hold the “Control Lock/Unlock” button for three seconds.
- Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.
How do I know if my thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown. Learn about testing for a blown fuse.
How do I know if my dryer thermal fuse is blown?
How to Tell if a Thermal Fuse is Blown
- Unplug your dryer and ensure it is no longer connected to the gas or electric.
- Locate the thermal fuse, as above.
- Disconnect the thermal fuse from the wires.
- Test the fuse with a multimeter.
- If the needle on your multimeter does not move, your thermal fuse is blow.
How do I reset my thermal fuse?
- Step 1: Locate the Fuse. Study the owner’s manual for the location of the thermal fuse. …
- Step 2: Cut Power to the Dryer. …
- Step 3: Disassemble as Needed. …
- Step 4: Disconnect the Thermal Fuse. …
- Step 5: Conduct a Continuity Test. …
- Step 6: Purchase a Replacement. …
- Step 7: Replace the Fuse. …
- Step 8: Reassemble the Dryer and Test It.
How do I know if my thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
Can a dryer thermal fuse be reset?
You can reset a thermal fuse. … It isn’t just clothes dryers that have thermal fuses; pretty much any appliance that heats up has one, including your washer, microwave oven, standard electrical oven, dishwasher and room heater.
How can you tell if a dryer heating element is bad?
Inspect the metal wire coil for any breaks in the wire. If the wire is solid and has no breaks in it, the heating element should be good. If the wire has a break in it, the heating element is defective.
Will dryer run if thermal fuse is blown?
A gas dryer will run but won’t heat if its thermal fuse blows because the dryer overheated (usually because the vent is clogged, so check the vent path).
How can you tell if a dryer heating element is bad?
Inspect the metal wire coil for any breaks in the wire. If the wire is solid and has no breaks in it, the heating element should be good. If the wire has a break in it, the heating element is defective.
Where is the reset button on a dryer?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
How much does it cost to replace a thermal fuse in a dryer?
Other Costs to Fix a Dryer
| Part | Material Cost | Total Cost |
|---|---|---|
| Thermal fuse | $5-10 | $80 -$130 |
| Dryer thermostat | $3-20 | $180 |
| Bearing | $50 | $130-$250 |
| Roller | $10-30 | $90-$230 |
Why is my Whirlpool Duet dryer not spinning?
If your Whirlpool dryer won’t spin properly, the drum rollers may be worn out. You can check the rollers for wear and tear to see if they turn easily. If any of the drum rollers are damaged or don’t spin easily, we recommend replacing all of them at the same time as a preventative measure.
Is Whirlpool Duet discontinued?
Whirlpool’s earlier Duet (Sport) WFW8500S Washer has been discontinued and has been replaced with a line of Duet front load washers. …
Where is the Control Lock button on a Whirlpool Duet dryer?
Locate the “Control Lock” button, which is often located on the right side of the control panel of Whirlpool Duet models.
How do you put a Whirlpool Duet dryer in diagnostic mode?
press and hold for three seconds, release for three seconds; press and hold for three seconds. You’ll know you’ve entered diagnostic mode because all the indicators on the console will light up for five seconds and you’ll see the code “88” in the Estimated Time Remaining display.
