If the Whirlpool washer displays the de error code on display, so there are problems with a door.
…
Manual Review
- Unplug the Whirlpool washing machine from the mains.
- Wait for 15-20 minutes while the control unit reboots.
- Reset the error by pressing the START button (On/Off).
- Check hatch locking.
Likewise, Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Also, What is E1 error in Whirlpool washing machine?
E1 – water inlet alarm
Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.
Moreover, What is PE error in Whirlpool washing machine?
Whirlpool PE – PRESSURE SENSOR ERROR // Water level pressure switch error.
How do I reset my Whirlpool front load washer?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do I reset my Whirlpool washer after a power outage?
How do I reset my Whirlpool washer after a power outage?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. …
- The motor has now been reset and is ready for you to start a cycle.
Why is my Whirlpool washer not working?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
How do I fix E1 F9 error on Whirlpool washer?
Filter clogged
It picks up trash and small objects before they reach the pump, instigating error code E1 F9. To access the filter, unscrew and remove the front panel. Then gently turn it and remove it from the groove.
How do I fix E1 error on my washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
Why does my washer keep saying E1 F9?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. … If not, the washer could siphon (fills and drains at the same time). Lower drain hose if the end is higher than 96″ (2.4 m) above the floor.
How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Why is my Whirlpool front load washer not draining?
You need to make sure that the drain hose is not kinked at all. Straighten the hose to make sure that there is enough water flow and that you also remove any blockages from the drainpipe well. Ensure that you are using a U-shaped drain and secure it properly. Your instruction manual will show you how to do this.
How do I reset my front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do you manually unlock a Whirlpool front load washer?
Reach up inside the front panel and locate the door latch assembly on the right side of door. Feel for a tear-drop shaped tab on the bottom of the door latch assembly. This tab will manually unlock the door.
How do you reset a washing machine after power outage?
Turn the machine on with dry hands. If it still won’t start, unplug it or turn the circuit breaker off, then back on until the breaker firmly clicks in place and plug the machine into the outlet. Push the restart button. Some machines may require you set the knob to a specific setting for the reset feature to work.
Why is my washing machine not turning on?
Power Source
Make sure the machine is tightly plugged in. Next, check for a tripped circuit breaker. Reset the breaker and try to start the washer. If neither is at fault, you may have a damaged power cord.
How do I force my Whirlpool washer to open?
Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
What does F9 mean on Whirlpool?
During a power outage, if there was a surprising amount of power supply line “noise” that the control detected as an incorrect voltage amount, the control could display the F9, F9 E0, or PF Error Code.
What does E1 mean?
Acronym | Definition |
---|---|
E1 | Everyone |
E1 | Enterprise One (JD Edwards software) |
E1 | Echelon 1 (US DoD) |
E1 | European Basic Multiplex Rate (30 voice channels; 2.048 Mbps) |
How do I clear the error code on my Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you fix E1 F9 error on a Maytag washer?
F9 E1 Code in the display: Is the drain hose properly installed?
…
Is the drain hose properly installed?
- Make sure the drain hose is not kinked or clogged.
- Use the U-shaped drain hose form on the drain hose.
- The standpipe (drainpipe) height requirements are 96″ (244 cm) maximum and 39″ (99 cm) minimum.
What does code E1 F9 mean on Whirlpool washer?
F9 E1 Code in the display:
This error code indicates that drain times are longer than expected, typically over eight (8) minutes.
What do you do when your front load washer won’t drain?
Clogged Drain Hose
Over time, debris can clog the drain hose and prevent your washer from draining. A twisted or coiled drain hose can also inhibit the free flow of water. Check behind the washer and straighten a kinked hose. If this does not solve the problem, unplug and clean the hose to eliminate any residue.
Why is my front loading washer not draining?
A washing machine not draining is one of the most common problems we encounter. It can be caused by one of the following: – The drain hose or pump is clogged with a small item of clothing, residual gunk or other debris. – The washer is malfunctioning and not engaging the drain/spin cycle properly.
How do you run a diagnostic on a Whirlpool Duet washer?
Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)