If your washing machine is not working correctly it’s safe to say it’s developed a fault. A flashing FP or F9 E1 error code on the LCD display can ring alarm bells, but it’s typically associated with a water draining problem inside the drum.
Table of Contents
READ ALSO
Likewise, How do you fix E1 F9 error on a Maytag washer?
F9 E1 Code in the display: Is the drain hose properly installed?
…
Is the drain hose properly installed?
- Make sure the drain hose is not kinked or clogged.
- Use the U-shaped drain hose form on the drain hose.
- The standpipe (drainpipe) height requirements are 96″ (244 cm) maximum and 39″ (99 cm) minimum.
Also, How do I fix E1 error on top loader washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
Moreover, How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do I clear the error code on my Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I reset my Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
What does E01 and F09 mean on a Maytag washer?
Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
How do I fix error F8 E1?
Error Code F8 E1, LF, or LO FL all indicate that no water is detected entering washer after 13 minutes.
…
Remove F8 E1 Error Code:
- Unplug the washer or disconnect the power for one minute.
- Plug in the washer or reconnect the power.
- Re-select the cycle and press Start.
Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Why is my Whirlpool washer stuck on sensing?
A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.
Why does my Maytag washer not start?
If your Maytag washing machine isn’t starting, verify that the power cord is connected to a live outlet. Test the outlet with another three-prong appliance. … Select a wash setting and pull out the knob to start the cycle. If it still won’t start, reset the circuit breaker or change out the fuses if they are blown.
Why is my Maytag washer not working?
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.
Why does my Maytag washer not fill with water?
If your Maytag Washer keeps filling or won’t fill up with water, you should check your water for improper installation or kinks in your water supply lines, inlet valves, and drain hose. These issues can also signify a faulty part in your household appliance, which may need to be serviced or replaced.
Why is my Maytag washer stuck on sensing?
If your Maytag washer’s sensing light is stuck and will not move to the appropriate cycles, this is usually caused by a stuck or keypad. The keypad can occasionally become jammed or, if you have recently replaced a part on the washer, you may have forgotten to recycle the codes, which can lead to a stuck sensor light.
How do you bypass the clean cycle on a Maytag washer?
Hello Sandy, Press and hold the “Spin” and “Soil” button simultaneously for 10 seconds. A countdown will be displayed on the console. Once the countdown has completed the unit will have successfully reset.
Why is my washer stuck on sensing?
When Kenmore HE Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, most likely one of these 3 parts malfunction: Failed Water Inlet Valve or Inlet Valve Tap is in OFF position. Shift Actuator not able to change position, before Wash cycle. Control Board malfunctioned.
How do I fix E1 error on my washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
How do I fix E01 on my washing machine?
How to Diagnose and Fix Fault Code E01
- Switch off and unplug your machine.
- Check the door lock itself. (Sometimes the plug on the lock can melt.)
- Check the wiring to the door lock.
- Check the wiring to the control board from the door look.
How do I clear F9 code?
How to Remove the F9 Code From Maytag
- Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. …
- Open the oven door and check the door latch. …
- Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. …
- Press the oven door shut gently. …
- Test the oven.
What does F8 E1 mean?
If F8 E1 or LF (too long to fill) appears in display, it means the washer is taking too long to fill. It’s possible the drain hose extends more than 4.5″ (114 mm) into standpipe. … This washer has sensors which detect the water supply, and requires both hoses to have water going to the water valve.
Why does my Whirlpool washer says add garment?
Detergent Low (on some models) – When detergent in the bulk dispenser is running low, the display will show the detergent level (Low). Add Garment – When “Add Garment” is displayed, you may pause the washer, open the door, and add items. Touch and hold START/PAUSE to start the appliance again.
What is E1 error in AC?
If your air conditioner displays E1 in the display panel and won’t turn on, it means that the Room Thermistor (a device connected to the thermostat that detects room temperature) is shorted or defective, and you need to have your air conditioner serviced.
Why is my Whirlpool washer not working?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
