Why does my washer says D5?

You may get a D5 error after washing a load, and the washing machine door will not open. Or more typically, the machine will display a D5 error after loading the washer and closing the door. The door may be closed – but a D5 error means it is not properly locked to prevent opening during a cycle.

Likewise, What does SU D5 Electrolux?

You may have the code reversed. The Sd in your display window is indicating a SUDS LOCK (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE). If suds are detected continuously by the water level pressure switch during drain or spin phase, the washer will fill with 4 liters of water and then rest for 5 minutes.

Also, Why is my Samsung washer not draining?

It could be because the washer isn’t level or the drain tube is clogged or pinched. Adjust the legs of your washer, as needed, and check the drain tube for kinks or damage. Troubleshoot a Samsung washer not draining with these likely causes and straightforward solutions.

Moreover, What does the DC code mean on a Samsung washer?

By Lyle Weischwill. A dc error code on your Samsung front-load washer means the washer won’t spin because the load is unbalanced. Fixing a dc error code can be as easy as redistributing an unbalanced load or adding a few garments to a small or single-item load.

How do you clear the error code on an Electrolux washing machine?

Press and hold the far left key under the display and “CANCEL” buttons simultaneously for 3 seconds. The code(s) will be cleared.

Why does my Electrolux washer say suds?

If your washing machine displays SUDS on the screen, it has detected an over-sudsing condition, and will stop for a short period to allow the suds to dissipate. This error code is usually caused by too much detergent, or the wrong type of detergent.

How do I manually drain my Samsung washer?

[Solution]

1. 1 Unplug the washing machine from the power supply.
2. 2 Open the filter-cover.
3. 3 Unscrew the emergency drain cap by turning it to the left.
4. 4 Grip the cap on the end of the emergency drain tube, and then slowly pull it out about 15 cm (about 6 inches).
5. 5 Allow all the water to flow into a bowl.

How do I fix my Samsung front load washer that won’t drain?

If the washer won’t drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.

How do I know if my washing machine drain hose is clogged?

An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump. If the hose is worn or badly kinked, replacing the hose may improve the ability of the machine to pump water.

How dO you rebalance a Samsung washing machine?

How do I run Calibration Mode on my Samsung washing machine?

1. 1 Turn the washing machine off and then on again.
2. 2 Hold down the Temp and Delay End + buttons for 3 seconds until a “CB” code appears on-screen. …
3. 3 Press Start/Pause to run the Calibration cycle.

How do you rebalance a Samsung washer?

1. Remove all laundry or any other contents in the machine.
2. Press POWER on the control panel of the lower washer to turn the washer on.
3. Press and hold Temp. …
4. Press START/PAUSE on the lower washer control panel to start Calibration.
5. When complete, the lower washer turns off automatically.

How do I get my Samsung washer to spin only?

To run a Spin Only cycle on a model that does not have this option on the cycle selector dial, perform the following:

1. Power the unit on.
2. Press and hold the spin key for approximately 3 seconds. A chime will sound.
3. Select the spin level, if desired.
4. Press the Start/Pause button.

How can I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

What does E 10 mean on washing machine?

Issue. Washer dryer displays error message E10, C1 or emits 1 beep / 1 flash. It indicates a problem with not taking in water, not taken in enough water or problems with the drain.

How do I fix the Sud error on my washing machine?

How to fix the error

1. Wait for a little for the suds to dissipate. …
2. Clean the drain filter upon completing the wash cycle;
3. Remove excess powder by running the washing machine without clothes and setting a long wash cycle and high temperature;
4. Change the detergent if you notice a lot of suds.

Why does my washer keep saying Sud?

It means you are using detergent improperly. If your washing machine has the word “SUDS” on the display, it has detected an over-sudsing condition, and will stop for a short period to allow the suds to dissipate. This error code is usually caused by too much detergent, or the wrong type of detergent.

Why won’t my Samsung washer drain and spin?

If the drain hose is pushed in too far or an airtight connection is made, a syphoning effect will force water and air back into the washer. This can result in the washer not being able to drain, fill or spin.

How do you force a washing machine to drain?

How to Drain a Top-Loading Washing Machine

1. STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one. …
2. STEP 2: Locate the drain hose and water supply hoses. …
3. STEP 3: Drain the washing machine of water. …
4. STEP 4: Remove a drain hose clog. …
5. STEP 5: Remove a drain pump clog.

Where is the drain filter on my Samsung washer?

All current Samsung Front Load Washers have debris filter access panels located on the front of the unit (bottom left or bottom right). The filter is housed inside of the drain pump to prevent the drain hose from being clogged. If not cleaned regularly, unpleasant odor, draining, and filling issues will arise.

How do I troubleshoot my Samsung front load washer?

Troubleshooting

1. Unplug the machine. …
2. Disconnect the hoses.
3. Remove the detergent drawer by pressing the central locking button.
4. Open the hatch of the drain filter at the bottom of the front panel.
5. Empty the water and clean the filter.
6. Put the washer on a side so that you can access the bottom.

Why is my Samsung front load washer not spinning?

If your washer isn’t spinning properly , it could be because of an unbalanced load, which makes it harder for the drum to spin. An unblanced load also cause errors. “Ub” or “Ur” display is one of the sign that your washer is unbalanced. This may be because the washer is lopsided or because the load inside is uneven.

Why won’t my Samsung washer Drain and spin?

If the drain hose is pushed in too far or an airtight connection is made, a syphoning effect will force water and air back into the washer. This can result in the washer not being able to drain, fill or spin.

How do you unclog a washer machine?

To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.

How do you unclog a washer drain hose?

1. Unplug the washer and put the plug on top of the machine to keep it out of any spilled water.
2. Take any wet clothes out of the washer and bail the water out of the drum with the bucket. …
3. Pull the washer out from the wall enough for you to get behind it.
4. Locate the drain hose. …
5. Check the drain hose for kinks and bends.