The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. Press PAUSE/CANCEL twice to clear the display. If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
Table of Contents
READ ALSO
Likewise, Why does my washer say F?
The F indicates that the washer control detected a component problem. If the F code was caused by excessive suds preventing the washer from draining, you may be able to shut the door and run a drain/spin cycle to remove the water from the washer.
Also, How do I run a clean cycle on a Maytag washer?
STEP 1: CLEAN THE TUB
- Remove any items left in the tub.
- Add an affresh® washing machine cleaner tablet to the bottom of the tub. …
- Close the door and select your washer’s cleaning cycle.
- For top load washers, when the cycle ends, run a rinse and spin cycle to clear away any excess cleansers.
Moreover, What are the codes for a Maytag washer?
Error Codes in your Maytag Top Load Washer:
| Error code | Error |
|---|---|
| Ofb | The washer load is out of balance. |
| OL | The washer load too large. |
| PF | The wash cycle was interrupted by a power failure. |
| Sud | There are excessive suds in washer. |
• 16 juin 2020
What does the Code F mean on a Whirlpool washer?
The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won’t run at all.
What does F code mean?
FCODE
| Acronym | Definition |
|---|---|
| FCODE | Forth Code (electrical engineering) |
What does it mean when a washer says F1?
When the Whirlpool Cabrio displays an F1 error, this means the the control board is having difficulty communicating with the motor. To fix your F1 error, you can first try to unplug your washing machine for 15 minutes and then plug it back in.
How do you bypass the clean cycle on a Maytag washer?
Hello Sandy, Press and hold the “Spin” and “Soil” button simultaneously for 10 seconds. A countdown will be displayed on the console. Once the countdown has completed the unit will have successfully reset.
Why does my Maytag washer take so long to wash?
A washer that continuously takes too long to wash may have a malfunctioning load sense system, or greater problems with its control panel. There may also be issues with your water inlet valve, which pulls water into the appliance for each cycle.
How long can I pause my Maytag washer?
On model mvwx655dw , when the start/pause button is pressed the cycle will remains paused with the lid open for 10 minutes, the washer will pump out the water.
Can you reset a Maytag washing machine?
If an error message causes your Maytag washer to not run properly, reset the washer to clear the error message. You also can reset the washer if you want to cancel a setting you chose.
What does the code CL mean on a Maytag washing machine?
Possible Solution
The CL code is a reminder to run the Clean Washer cycle and will appear after 30 cycles. The code will automatically clear once a Clean Washer cycle has completed or after three cycles. CLICK HERE for additional information on cleaning.
How dO you reset the code on a Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How dO you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does E DL mean on a washing machine?
E:dL – Door Lock Error – Open and close door. Check door lock and switches. E:dO – Door Open During Running Cycle – Make sure door is properly closed. Check door lock and switches for defects. E:dr – Drain Error – Maximum drain time exceeded or water is still being detected at end of spin cycle.
Why does my washer say dL?
: DL is a failure of the door to lock. The door must lock before any cycle begins. … Machine/Motor control is detecting an open door/lid switch when it attempts to lock. Machine/ Motor control can not determine if the door/lid switch is in a locked state.
How do I fix F1 error on my washing machine?
To fix your Whirlpool F1 error code, you should first try to unplug your washing machine or disconnect power for 1 minute and then plug it back in/turn the power back on. Re-select the cycle and press Start. In some cases, disconnecting and reconnecting power to the unit clears the F1 error code.
How do I reset my front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do I fix F01 error?
The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.
What is the power wash setting on Maytag washer?
PowerWash® Cycle – The PowerWash® cycle features a combination of more wash action and heated water to drive powerful cleaning. PowerWash® Agitator – The PowerWash® agitator tackles any load size with both efficient, concentrated cleaning to fight stubborn stains and robust wash action to help break up messes.
How long is the normal cycle on a Maytag washer?
Best answer: The washer takes anywhere from 45 minutes to an hour to complete a cycle using the Normal Wash Cycle. Some other factors to consider is how long the machine takes to fill to do the laundry in the Normal Wash cycle and how much water pressure you have coming to the machine.
Why does my Maytag washer smell?
Wet laundry that sits in the Maytag washer for long periods may cause the machine to smell. Fungus and mildew thrive in moist environments; the dark, dank tub of wet laundry becomes the ideal breeding ground for bacteria and odors.
What is the power wash setting on a Maytag washing machine?
PowerWash® Cycle – The PowerWash® cycle features a combination of more wash action and heated water to drive powerful cleaning. PowerWash® Agitator – The PowerWash® agitator tackles any load size with both efficient, concentrated cleaning to fight stubborn stains and robust wash action to help break up messes.
What’s the quickest wash cycle?
The 15-minute cycle is the shortest of the washing programmes. It predicts a 5-minute wash, a rinse and a fairly energetic centrifuge.
Is there a quick wash option on Maytag washer?
Luckily, Maytag Washers are prepared with the Rapid Wash Cycle Feature! This wonderful feature allows loads to wash faster by cutting down on wash and spin time, while boosting motion and temperature to shorten the cycle without compromising on clean.
