The Error code LF stands for ‘Long Fill’. If the water filling time exceeds ten minutes, it means the water valves have turned off. LF flashes when the water level does not change for a period of time on or water is present but control does not detect the water level changing.
Table of Contents
READ ALSO
Likewise, How do you fix LF error on a hot tub?
For the error messages of HFL, LF, Dr, or DRY. This means that there is a flow issue through your heater. Try and clean your filters. While cleaning your filter make sure there is no debris in your hot tub that will get sucked down into your pump.
Also, Where is the water inlet valve located on a washing machine?
The inlet valve can be found on the back of your washing machine. Its principal responsibility is to manage the entry of water into your washing machine. In other words, the inlet valve acts as a sort of gate keeper, allowing water to flow into the tub when it receives certain electrical signals from the washer.
Moreover, Why does my Maytag washer not fill with water?
If your Maytag Washer keeps filling or won’t fill up with water, you should check your water for improper installation or kinks in your water supply lines, inlet valves, and drain hose. These issues can also signify a faulty part in your household appliance, which may need to be serviced or replaced.
What does code LF mean on hot tub?
LF = Persistent low flow problems. (Displays on the 5th occurrence of “HFL” message with 24 hours). Heater is shut down, but other spa functions run normally. dr = Inadequate water detected in heater.
What does code SL mean on hot tub?
SL: Sleep –
Sleep mode will only allow the spa to heat within 20 degrees of the set temperature.
What does HL mean on hot tub?
The HL reading in the display stands for Hi-Limit. The hi-limit is measuring the temperature at the heater, not the actual water temperature of the spa. if your spa is reading HL, it will not allow your heater to turn on and therefore you will notice the pumps will be running close to 24 hours a day.
How do I know if my inlet valve is bad?
Signs that point to an inlet valve problem include leaks that fill the dishwasher when not running, the dishwasher filling too slowly when in use, or the dishwasher not filling at all. Leaks that end up outside of the dishwasher also can indicate an inlet valve problem, and this must be addressed immediately.
Can you fix a water inlet valve?
There is little that you can do to repair the valve itself, but you can clean the two inlet ports to restore full water flow. You can also test the valve to determine whether it has failed. Replacing a bad valve is a simple job and must be done with parts and procedures that are specific to your washing machine model.
How do you fix a Maytag washer that won’t fill with water?
Maytag Washer fills slowly or will not fill at all
First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
What does f7 mean on a hot tub?
This sounds like a filter mode. See if all pumps are pulling proper water, and that the spa has good water flow back to spa.
What does F4 mean on hot tub?
The Big List of Spa and Hot Tub Error Codes
| CODE | ERROR CODE DESCRIPTION |
|---|---|
| F4 | 8 hours daily filtration; system message, not an error |
| F6 | 12 hours daily filtration; system message, not an error |
| F | Fahrenheit, used to indicate panel is in Fahrenheit mode |
| FB-ER | Fiber optic error; accent lighting |
How do I fix the HH code on my hot tub?
Open the spa cover and let the spa cool down for 10 minutes, then touch the control panel to reset the circuits, or push a red reset button on air systems. For OH, HH or HOT trouble codes, an overheating hot tub is not usually a heater problem. It is almost always a flow problem.
What does SL mean on CleverSpa?
A SL Error Code showing on your CleverSpa® Control Panel can mean there is a blockage in the system which is preventing hot water from circulating.
What mode should my hot tub be in?
By default filter modes are 2 hours in the morning and 2 hours in the evening, the rest of the time the hot tub will use the insulation to keep the spa warm and retain heat. Economy is a good setting for those who use the hot tub daily.
What does F4 mean on a hot tub?
The Big List of Spa and Hot Tub Error Codes
| CODE | ERROR CODE DESCRIPTION |
|---|---|
| F4 | 8 hours daily filtration; system message, not an error |
| F6 | 12 hours daily filtration; system message, not an error |
| F | Fahrenheit, used to indicate panel is in Fahrenheit mode |
| FB-ER | Fiber optic error; accent lighting |
Why is my Cleverspa saying HL?
An HL error usually means there is a blockage, preventing water from circulating around the pump & heating system.
Is there a reset button on a hot tub?
A spa heater has a high-limit reset button. A spa or hot tub provides a form of personal relaxation known as hydrotherapy. … A spa heater may need to be reset if it has tripped or stopped working. Using the high-limit reset switch and checking all breakers and GFCI outlets can reactivate the spa’s heater.
Can you clean a water inlet valve?
Washing machines pull in water from your home’s water supply and mix it with detergent in the laundry tub. … It is a good idea to clean the water inlet valve on your washing machine every year or so.
How much does it cost to replace a washing machine valve inlet?
Machine Inlet Valve Repair
A washing machine inlet valve replacement costs $75 to $125.
How much does a water inlet valve cost?
Replacing a washing machine inlet valve can cost up to $125.
How much does it cost to replace a washing machine valve inlet?
A washing machine inlet valve replacement costs $75 to $125.
Why is the water not coming out of my washing machine?
Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.
Why is my washer not adding water?
If your washer doesn’t fill with water, first check that the house water supply to the washer is on. If it is, and the washer won’t fill at all, the inlet valves might have failed. If the washer fills partially, the problem is likely with the temperature selector switch or water-level pressure switch.
How do you adjust the water level on a Maytag washer?
To raise the water level, turn the adjustment screw clockwise; to lower the water level, turn the screw counterclockwise. The water level must be below the top of the tank’s overflow tube.
