Samsung Oven Error Codes
Table of Contents
READ ALSO
| Error Code | Solution |
|---|---|
| C-21 | This code occurs if the internal temperature rises abnormally high. Touch OVEN OFF, and then restart the oven. If the problem persists, disconnect all power to the oven for at least 30 seconds and then reconnect the power. |
• 29 févr. 2020
similarly, Why does my stove says bad line?
The bad line means that the oven is only getting 120 volts, which is not enough to run the oven properly. Plug the unit back in. The circuit breaker should be turned off. The back access panel should be removed if it still doesn’t work.
on the other hand, What does C 24 mean on a Samsung oven?
C-24. The temperature sensor has detected the temperature of the oven rising at a higher than normal rate. This is generally caused by the vent, which is located at the center of the back of the cooktop, being blocked or partially blocked. If the vent is covered by something, like a pan, remove it.
also, What does C do mean on Samsung oven? C-d0. Control buttons are. pressed over 10 seconds. Clean the keys and check if there is water on the surface around key. If it occurs again, turn off the microwave oven over 30 seconds and try setting again.
What does C 31 mean on a Samsung oven?
Which means error code C -31. Error code C-31 means the following – the circuit board of the electric range, was overheated. … Because the PCB has been overheated, this can lead to a critical fault, which in turn is unsafe and can lead to a fire.
Why does my Samsung oven say bad LinE?
bAd LinE. The power connection is plugged in improperly. Reconnect the power connection properly. Refer to the installation manual or a professional installer.
What does F4 mean on a GE oven?
F4 fault code usually means that the oven sensor needs to be replaced. Fault codes are programmed in all electronic ranges. These codes help GE Appliances Factory Service technicians quickly diagnose issues.
What does bad LinE mean?
a bad (telephone) line: a bad or poor (telephone) connection. noun.
Why does my stove say C do?
That is a control shorted key code, when you get that code you will need a new touchpad for the unit. You can try and unplug the unit for a full minute and reset it, but if it is new and under warranty I would have it fixed for free.
Why does my Samsung oven say end?
When the set time has elapsed, the oven will beep and the display will show “End” until you press the Timer pad. To cancel the timer at any time, press and hold Timer for 3 seconds. This will return the display to the clock view.
What does C-do mean on a microwave?
Samsung Microwave Error: C-DO. Error Code Definition: Door Or Key Error.
How do I clear error codes on my Samsung oven?
Unplug the range for 3 minutes to reset the oven electronic control board. If the code appears after you plug the range in, unplug the range and secure any loose wiring connections. Replace any damaged wire harnesses. If the problem persists, replace the oven electronic control board.
Why does my Samsung microwave say C 10?
Errors C-10, C-11, C-12 | Samsung Microwave Oven. The samsung Microwave Oven Error C-10, C-11, C-12 is an error showing some trouble with the Gas or PH sensor. These errors are very common errors in this brand of Microwave Ovens.
How do you reset a Samsung Galaxy Flex Duo oven?
Unplug the range for 3 minutes to reset the oven electronic control board.
…
Reset the electronic control.
- Turn the breaker to the OFF position.
- Wait one minute, then turn the breaker back to the ON position to reset.
- This needs to be done even if the light or the clock on the range is working.
What does C do mean on Samsung microwave?
The C-DO error code typically occurs when a button has been pressed for 10 seconds or more. Please, reset the unit by cutting the power for 2 minutes.
How do I fix the F2 code on my GE oven?
If the F2 error code has frozen on the oven after shutting down, then unplug the oven for 30 seconds. Plug the oven back in and see if the error code appears again. At times glitches will occur and the error code will randomly appear.
What does F4 code mean?
F4. This code usually means that the oven sensor needs to be replaced. F5. This code usually means that the electronic control needs to be replaced.
What does F2 mean on a GE oven?
If you have a GE oven, the error code F2 on the oven means that the temperature sensor has detected a temperature in excess of the preset threshold. The cause could be a sensor malfunction.
What does 5E mean on Samsung stove?
Actually SE error is 5E. Users confuse a number with a letter because of similar writing. It signals the presence of one or more problems in the keyboard area. First, you need to make sure that there is no failure on the control board.
Do Samsung ovens turn off automatically?
Is there any other reason for a cooking zone to switch itself off? … It automatically turns off any cooking zones if things have been left cooking on them for a long period of time or if there’s no change in the operation after a certain period.
Why won’t my Samsung oven heat up?
Defective Igniter. In gas ovens, a defective igniter is often responsible for a Samsung oven not heating up. … If the gas takes more than 90 seconds to ignite, the igniter may be too weak. When the gas doesn’t light at all, confirm that the igniter is defective with multimeter testing.
What is smart control on Samsung oven?
Use Smart Control on your range
Your range can be controlled remotely once it’s been connected to the SmartThings app. After you close the door, press Smart Control on your range’s display to activate the feature. The feature will be canceled once the door is opened, or once you finish or cancel cooking.
What does code C do mean on Samsung microwave?
The C–DO error code typically occurs when a button has been pressed for 10 seconds or more. Please, reset the unit by cutting the power for 2 minutes.
What does 1S mean on microwave?
The “1S” and “2S” normally mean “one stage” and “two stage” cooking.
What does it mean when your microwave says sensor error?
The error message is caused by opening the microwave door too early when you are using the sensor cooking function. Removing the error message from the microwave display takes only a moment.
Don’t forget to share the post !
