Drain Hose Issues
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already.
similarly, What do you do when your Whirlpool washer won’t spin?
As a safety feature, Whirlpool washers will not spin if the lid switch is not activated; ensure the lid is properly closed and, if it is and the spin cycle is still not activated, you may need to replace the lid switch.
on the other hand, What causes a Maytag washer not to spin?
One of the most common reasons for a Maytag top load washer not spinning is an incorrect wash cycle or spin setting. GENTLE, HANDWASH, or DELICATE settings utilize slower spin speeds for more fragile fabrics. Some model washers also allow you to vary the spin speed, making it slower or more rapid, for different loads.
also, Why is my Maytag washer not draining or spinning? Drain Hose is Kinked or Clogged
A hose that’s kinked or clogged by lint or debris causes a washing machine not to drain because water can’t bypass the blockage. … To remove any kinks, disconnect the hose clamp at the washer and gently straighten the hose. The hose must also be unclamped to assess any blockages inside.
Why is my spin cycle not working?
An unbalanced load of laundry is one of the most common causes of an inadequate spin cycle. Sometimes clothing can settle on one side of the drum, throwing off the motion of the washing machine. … If you suspect a distribution problem, try rearranging your clumped-up wet laundry and running the spin cycle again.
Why is my Whirlpool washer stuck on spin cycle?
The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer will not spin. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If the lid switch does not have continuity, replace it.
How do you reset the spin cycle on a Whirlpool washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I reset a Maytag Centennial washer?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
- The motor has now been reset and is ready for you to start a cycle.
How do you reset a Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
What do you do when your washing machine won’t spin or drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do you force a Maytag washer to drain?
Here’s how to manually drain water from a Maytag washing machine:
- Pull the washer away from the wall and turn off its power and water connections.
- Scoop out any remaining water in the washer drum.
- Unhook the drain hose from the wall or sink drain and empty residual water into a bucket.
What causes a Whirlpool washer not to agitate?
When your Whirlpool washer won’t agitate, spin, or drain, the culprit could be a defective drive block. The drive block connects the agitator to the washer transmission. … If the drive block is worn out, the agitator may move a little or not at all, even when the transmission shaft is still moving.
Why is my washer stuck in spin cycle?
If you have a GE washer that’s stuck on its spin cycle, you’ll need to reset the machine. This is because the appliance is full of water during this cycle, and merely turning off the washer will leave it filled with water. … If you’re having GE Hydrowave washer problems, unplug the appliance from its outlet.
Why is my washer stuck on the rinse cycle?
If your washer works fine up to the point of the rinse cycle, this is a likely sign that your cold water supply faucet has malfunctioned, since this is the point at which cold water is needed. … It is also possible that the water filters inside the pipes leading into the washer have become clogged.
Is Maytag Centennial washer high efficiency?
It lacks superfluous features, but still features a high efficiency design and an electronic control panel. Those controls are laid out from left-to-right, starting with “How dirty is it?” and finishing with, “Are you going to add fabric softener?” There is no Quick cycle.
What do you do when your Maytag washer won’t start?
If your Maytag washing machine isn’t starting, verify that the power cord is connected to a live outlet. Test the outlet with another three-prong appliance. If the outlet is working, plug the power cord securely into the outlet. Do not use an extension cord or adapter.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
How do I know if my shift actuator is bad?
When the actuator fails there is usually and awful lot of grinding noise, and the tub and agitator operate at a slow speed, if at all. In most models, you will have an F7 -E1 or E5 error code in the display.
Does Spin Cycle drain water?
It removes the water from the tub during the spin cycle. The washer pump forces water from the bottom of the machine into the drain hose. The drain hose loops to the top of the machine, and then down to the drain, enabling the tub to fill. When the water reaches the bend in the hose, it goes out of the drain.
How do I reset my Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
What causes a washing machine to not drain completely?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
What does it mean when a washer won’t agitate?
If your washer won’t agitate but spins, a broken agitator may be to blame. … The output shaft of the transmission is splined to the agitator to secure it in place. Over time, some of the components of the agitator can wear down or break with normal usage, causing your washing machine not agitating issue.
How do you reset the spin cycle on a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do you reset the cycle on a washing machine?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do you reset a Centennial washing machine?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
- The motor has now been reset and is ready for you to start a cycle.
Don’t forget to share the post !