Press and hold for 3 seconds the “Control Lock/Unlock” button on the control panel to unlock the control panel. The “Control Lock” status light is goes out when the control panel is unlocked. In addition to Oldturkeys answer, try unplugging it for five minutes to allow it to reset.
similarly, How do you reset a Samsung dryer?
In the Settings menu, find Backup & reset, then tap Factory data reset and Reset phone. You’ll be prompted to enter your passcode and then to Erase everything.
on the other hand, Why does my dryer Says control locked?
The “LOC” indicates the (Control Lock). This means the control panel has been locked and it will have to be unlocked before you can use the dryer. To unlock the control panel; press and release the Option and Select buttons at the same time.
also, What does control lock mean on dryer? The dryers have a control lock feature, which prevents children from starting the dryer if they press the buttons on the control panel. The control panel is lockable whether the dryer is running or not, and when locked, all buttons are disabled.
How do I run a diagnostic on my Samsung dryer?
Run a Vent Blockage test
- When you’re ready to start, make sure the drum is empty and then close the door. …
- Press POWER to turn the dryer on and within 5 seconds, press and hold Adjust Time Up + Dry Level until InS or In appears on the display.
How do I reset my Samsung tumble dryer?
Resetting your dryer is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dryer (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.
Why isnt my Samsung dryer working?
When your dryer doesn’t power on, it could be something as simple as a tripped breaker or loose power cord. … Always switch off the circuit breaker before interacting with the dryer’s power cord, to avoid electric shock.
How do I turn off the control lock on my dryer?
The control lock is turned on or off by pushing and holding the drain/spin button for 3-5 seconds. See the image below. If the control lock light does not toggle on and off has your pressing and holding the button then it is possible the inter face is defective.
How do you clear the CL code on a LG dryer?
For most models, press and hold the key labeled CHILD LOCK (secondary function) for 3 seconds to disable the Child Lock feature. Keep pressing & holding down button until CL indication disappears or LOCK icon turns off on the display panel. Unplugging the dryer & plugging it back in will not reset the LOCK function.
How do I turn off the control lock on my dryer?
Press and hold the Extended Tumble and – (minus) buttons for 3 seconds. The control lock icon will flash while locking/unlocking, stay on when locked, and turn off when unlocked.
Is there a reset button on dryers?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes. Then push the reset button. If there are no problems with the motor, switches, or electrical system, this should restart the dryer.
Does a dryer have a reset button?
Often, dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes. Then press this reset button.
How do I get the error code on my Samsung dryer?
If you get this error, power off the dryer, and then individually touch and release every button on the panel, working back and forth to reach all edges of each button. If any of the buttons are damaged, or the code returns after powering on the dryer, visit our Support Centre to request service.
Where is the dryer reset button?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
Why is my Samsung dryer blinking?
60 min is blinking or Extra Low light is blinking
When either of these lights are blinking, this means that the dryer is getting too hot. The most common cause is a clogged lint screen or vent system trapping heat in the dryer. Clean the lint screen, vent system, or both to correct the error.
How long do Samsung dryers last?
Your washer and dryer will last the same amount of time. A washer can last between 12 and 14 years, while a dryer lasts between 18 and 24 years. The washer and dryer should last a long time.
What are the symbols on Samsung dryer?
An icon is showing on my Samsung dryer
- Sensor Dry. This icon indicates a Sensor Dry cycle is currently running.
- Child Lock. Child Lock is turned on. …
- Delay Start. Delay Start is in use. …
- Filter Reminder. …
- Time Remaining. …
- Signal Off. …
- Mixed Load Bell. …
- Vent Check.
What does LC mean on Whirlpool dryer?
If you see the “LOC”, “lc” or “LC” code on the control, the control lock has been set. Disconnect the control lock setting. If you are unsure of how to disconnect the control lock for your model, see your Owner’s Manual.
How do you reset a GE dryer?
How do you reset a GE dryer? Turn the dryer off, then on again to reset it. Or you can press the reset button on the dryer plug.
What does extended tumble mean?
Extended Tumble provides 1 hour of no heat tumbling after the clothes are dry. If you are using the cycle Signal Adjust and you select the Extended Tumble option, a signal will sound at the end of the drying time and several times during the Extended Tumble cycle.
How do I run a diagnostic on my LG dryer?
To run the Smart ThinQ feature:
- Open the Smart ThinQ App in your phone.
- Press the POWER to turn on the dryer.
- Place the mouthpiece of your phone very close to the POWER button.
- Press and hold the TEMP. …
- Keep the phone in place until the tone transmission has finished.
How do you reset the check filter on a LG dryer?
Reboot Your Machine
- Unplug your machine.
- Press the ‘Start/Pause’ button for 8 – 10 seconds.
- Replug the machine immediately afterward and turn it on.
How do I get the control lock off my washing machine?
How do I turn off control lock? To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
Don’t forget to share the post !