Rinnai fault code 11 – No ignition. Check to make sure the gas is turned on at the water heater, gas meter or tank. Ensure the igniter is operational. If gas is being supplied to the tankless water heater and the igniter is working, call for an evaluation by a qualified plumber.
similarly, Why is my Rinnai water heater not working?
Check the water supply and ensure the water flow is at least 30 psi. Check the pump wiring, look for any loose, damaged, or broken connections, and replace if necessary. Drain the water tank and check the water inlet filter for any blockages. If it is clogged, clean it or replace it.
on the other hand, How do I fix error code 79 on Rinnai?
Error Code 79
- Inspect the wiring harness on the leak detector. …
- Inspect the heat exchanger and all the internal piping within the tankless. …
- If you don’t find any leakage, look inside the cabinet. …
- If you find evidence of water pooling, dry off the leak sensor as well as the inside of the cabinet.
also, How do I fix noritz Error 11? How to Troubleshoot a Noritz Code 11
- Find the gas valve connected to the Noritz water heater and turn the gas valve counterclockwise until it no longer turns to open it completely.
- Turn the power off to the unit by pressing the “Power” button. Run hot water from a nearby faucet. …
- Turn the hot water back off.
How do I fix my Rinnai Code 12?
If you encounter error code 12, you can try the following steps to fix the problem:
- Check gas is turned on at the gas metre or cylinder.
- Check gas is turned on at the water heater.
- Check there are no obstructions to the flue outlet.
How do I fix my Rinnai Code 14?
An error code 14 indicates that your Rinnai is over heating. The issue could either be the bi-metal safety switch or the thermal fuses. Remove the cover and look for discoloration on the surface of the heat exchanger in the area where the combustion box meets the copper section.
How do I find my Rinnai error code?
Contact your local professional water heater expert today!
If your water heater is connected to MC-91 or MCC-91, you can easily find the most recent error codes. Press and hold the ON/OFF button for two seconds and press the arrow “UP”, the last nine Rinnai error codes will appear and flash one after the other.
How do I reset my Rinnai WIFI module?
How To Factory Reset – Press and hold the Connect button (see below) on the module until the LED blinks WHITE, and then release. The module will reboot and the module LED turns solid RED when complete.
How do I get Rinnai error codes?
If your water heater is connected to MC-91 or MCC-91, you can easily find the most recent error codes. Press and hold the ON/OFF button for two seconds and press the arrow “UP”, the last nine Rinnai error codes will appear and flash one after the other.
How do I fix my Rinnai Code 65?
You can attempt to clear any Rinnai error code yourself by turning your hot water tap off and on again, and by pushing the on/off button on your monitor off, then on again. If the fault code remains then further action will be required to rectify the issue.
Where is the leak sensor on a Rinnai?
Locate leak sensing element at bottom of unit .
Why is my Rinnai beeping 11?
Rinnai error code 11 is an indication that there is no ignition in, or no gas supply to your hot water system. … Check your hot water system for any visible damage or loose parts. Locate your gas supply and ensure it is turned on. Test your gas supply by turning on a gas appliance, such as a stove-top.
How do I fix noritz Error Code 45?
To fix error code 45, you may need to have a licensed contractor assess the condition of your Noritz tankless water heater. If there are no visible signs of water or moisture, reset the unit by switching it off for at least 30 seconds. If the error code shows again after the reset, you will have to call for service.
How do I stop my Rinnai from beeping?
Low Fuel. Some propane-fueled water heaters emit a beep when they are low on fuel. How to Fix: Flush the heat exchanger as per the recommended flushing procedure found in the owner’s manual. To temporarily reset the code, press the ON/OFF button 5 times.
Why is my Rinnai beeping?
Your tankless water heater will “beep” and display an error code to alert you to a problem with the system. Tankless water heaters will alert you with an audible alarm when service is required, a component fails, or a gas or water leak is present.
What is code 12 on Rinnai heater?
If you’re getting Rinnai error code 12 on your hot water unit, it indicates that a flame failure has occurred on the system. In this instance, your hot water unit has not recognised that there is a flame in the burner box. … Incorrect gas pressure supply your hot water unit. Loose gas connections and fittings.
How do I fix my Rinnai Code 25?
Rinnai Error 25 Fix
- Turn off your hot water system.
- Locate your system’s condensate line.
- Inspect the line and remove any blockages.
- Check the condensate trap.
- Turn on your hot water system and see if the error code has gone.
How do I fix my Rinnai Code 19?
Rinnai error code 19 signifies that there is a problem with the electrical grounding. To fix the Rinnai error code 19, inspect all electrical components of the unit for electrical shorts.
How do I connect my Rinnai to WIFI?
Download the Rinnai app from the Apple® Store or Google® Play Store. 3. Connect the module to your Wi-Fi network. When setup is complete, the owner will have access to remotely monitor and control their Rinnai tankless water heater using their smart device.
How do you test a Rinnai Ignitor?
Igniter issues
Test the unit’s igniter for proper work by cycling the unit and checking if there is a spark. If there is no spark, look for the loose, bad, or no connection and the damaged element. Verify the correct voltage on the electric board when the unit is in the ignition cycle.
How does Rinnai recirculation work?
Wireless Motion Sensor
Mounted near the point of use, the motion sensor operates the recirculation system by detecting full-body movement up to 30 feet away.
What is the priority button on Rinnai?
1. Press the “Priority button” on the temperature controller. The Priority light will glow indicating that this controller is controlling the temperature and that the Rinnai water heater is ready to supply hot water.
What is code 12 on Rinnai?
If you’re getting Rinnai error code 12 on your hot water unit, it indicates that a flame failure has occurred on the system. In this instance, your hot water unit has not recognised that there is a flame in the burner box. … Incorrect gas pressure supply your hot water unit.
Don’t forget to share the post !
