How do I fix Fisher and Paykel dishwasher f1 error?

1. Locate the drain-access filter panel on the bottom of the drawer.
2. Remove the rack that sits above it.
3. Pull up to lift the drain filter and remove it from the machine.
4. Set the filter under the faucet to rinse it clean with cold water.
5. Reinstall the filter and confirm that it sits flush with the bottom of the DishDrawer.

similarly, How do you run a diagnostic on a Fisher Paykel dishwasher?

Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.

on the other hand, Why is my Dishdrawer not draining?

Disconnect the drain hose at both connection points. … Stagnant water may be trapped in the hose, so remove it carefully and pour any trapped water down the sink. Straighten the hose and look through it. If you can see obstructions, the drain hose is likely the cause of your drainage problems.

also, What does F1 mean on a Westinghouse dishwasher? An F1 error code on your Westinghouse dishwasher indicates that a leak is detected somewhere in the unit, whereas an F3 error code pinpoints the issue to a problem with the overflow protector. The overflow protector is normally located in the front left corner of the dishwasher tub.

What does F9 mean on a dishwasher?

A water pressure sensor is related to the F9 fault code on Glow-Worm boilers.

How do I fix E6 error on Fisher and Paykel dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.

Do Fisher and Paykel dishwashers use hot water?

Take note of water connection requirements. The dishwasher has a single valve water connection. We recommend a cold water connection for best performance and energy efficiency. The incoming water temperature should not exceed 25°C.

How do I reset my DishDrawer?

Reset Procedures for the Fisher & Paykel Dishwasher

1. Press and hold the button decorated with the key and lock image for five seconds.
2. Press the power button to turn off power to the Fisher & Paykel dishwasher.
3. Wait a few minutes and then press the power button to restore power.

How do I unlock my DishDrawer?

Unlock by powering your DishDrawer™ back on (unless Keylock is activated, see above). Press any button and open drawer within 30 seconds.

How do I fix F5 error on dishwasher?

– Also if you add water softener in inlet of water, water pressure might go down and cause issue with F5 error. The solution is to remove one filter from inlet pipe (given by IFB) The inlet pipe has filter at both ends, and it becomes too many filter once water softener is added in between, Outlet: – This is hilarious.

How do I fix the F3 error on my dishwasher?

It there is the F3 fault code on the display, there must be a leak in the bottom section of your dishwasher. When the base tray is full, the system activates the flood switch and shows the code. Pull out the dishwasher and tilt it backwards until the water drains completely. Use a tray or bucket.

How do you unblock a dishwasher?

How to unblock your dishwasher spray arms

1. With your appliance switched off and unplugged, remove both baskets.
2. Remove the centre bolt which holds the arms in place with an adjustable spanner.
3. Take the spray arms off the centre bolt.
4. Hold the spray arms under warm running water to remove any dirt and debris.

How do I fix error e1 F9 on Maytag washer?

Possible Solutions

Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. Also make sure that the drain hose end is higher than 36 inches from the floor.

What does f2 mean on sharp dishwasher?

This error message means that you have a leak under the floor pan. Please check the machine for leaks. At the bottom there is a float switch that triggers the Aqua stop in the event of a leak. Either you have to open the rectangular cover below the door to check.

How do I clear the error code on my KitchenAid dishwasher?

Control Panel Reset

When powering down the unit and turning it back on doesn’t work, it may be best to reset the control panel’s computer. This is done by pressing two buttons, one after the other, at least five times each for a total of 10 presses. The door must be completely shut while the buttons are being pressed.

Where is the flood switch on a dishwasher?

The anti flood switch is in the bottom of the bas of the dishwasher. If its activated try and pull the dishwasher out and tip it 45 degs backwards and the water should drain out from the base and that way the flood switch will reset itself.

What does E4 mean on a dishwasher?

Error message E4 in free-standing compact dishwasher indicates too much inlet water and/or a leak.

What does E2 mean on dishwasher?

E2 – Abnormally long drain time. Check to make sure that the drain line is not obstructed or bent in a way that restricts water flow. Make sure the drain line is routed below the height of the dishwasher and that it has not been extended. This will inhibit the ability of the drain function to operate properly.

Does Fisher Paykel heat water?

Yes it does – all dishwashers heat their own water. Wash water is not as hot as rinse water, by having its own heater it can regulate the temperature. There, heating elements heat the water to 130 to 140 degrees Fahrenheit. …

Why is my DishDrawer not draining?

Disconnect the drain hose at both connection points. … Stagnant water may be trapped in the hose, so remove it carefully and pour any trapped water down the sink. Straighten the hose and look through it. If you can see obstructions, the drain hose is likely the cause of your drainage problems.

Do dish washing machines heat their own water?

Modern washing machines, dishwashers and electric showers take cold water and heat it themselves so you don’t need a supply of hot water waiting for them in the tank.

Why does my Fisher and Paykel dishwasher beep?

First and foremost, check the hose of your dishwasher. If it is bent or broken, it may not be draining the water which results in activating the beeps. To fix it, if there is bent, you may be able to replace it yourself and if it is broken, you need to replace it with new one.

What does E5 mean on a dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code E5 is the first three program indicator lights flashing. There is a water supply hose that is bent or crimped. The drain hose is not high.

How do I fix E6 error on my dishwasher?

Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.

Don’t forget to share the post !