To enter diagnostic mode follow the steps below.
- Turn the power on at the power point but off at the machine.
- Press and hold WASH TEMPERATURE SETTING DOWN and then press POWER until the. machine gives 2 short beeps and lights up.
- Release the buttons after the beeps as the beeps indicate diagnostic mode has been entered.
similarly, How do you run a diagnostic on a Fisher Paykel dishwasher?
Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.
on the other hand, How do I reset my Fisher and Paykel top loader?
Factory Reset
- Turn the dial to select ‘Spin’.
- Touch and hold the ‘Delay Start’ ‘More’ , the ‘Delay Start’ ‘Less’ and ‘Options’ buttons together for 3 seconds will appear on the screen and the machine will beep.
- Your washer will now be reset to the default settings.
also, Why is my Fisher and Paykel washing machine beeping? If your machine is beeping every 5 seconds and the high water light is lit, it means the water level in the machine is too high for the drum to spin. You can remove clothes from the machine to clear this problem. This warning light can also indicate that you need to select a higher water level to complete the wash.
How do I fix Fisher and Paykel dishwasher f1 error?
- Locate the drain-access filter panel on the bottom of the drawer.
- Remove the rack that sits above it.
- Pull up to lift the drain filter and remove it from the machine.
- Set the filter under the faucet to rinse it clean with cold water.
- Reinstall the filter and confirm that it sits flush with the bottom of the DishDrawer.
How do I fix E6 error on Fisher and Paykel dishwasher?
Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.
Why is my Fisher and Paykel DishDrawer beeping?
The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. Press ► once to stop the beeping, and then again to clear the fault. / ► to resume the wash program.
Is there a reset button on a Fisher and Paykel washing machine?
Factory reset
Enter Option Adjustment mode (refer to ‘Option Adjustment’). Select the ‘Delicate’ cycle. The display will show . Touch and hold for 3 seconds to reset your washer to its factory settings.
How do I reset my Fisher and Paykel mw512?
Turn the machine off. Press and hold the wash temp down button and then press and hold the power button together until the machine gives you 2 short beepts and lights up.
Why is my Fisher and Paykel not spinning?
Your washer should be on a level surface to prevent it moving during a cycle. Straighten any kinks along the hose that drains water from your washer. … If the kinks return, you may need to replace the hose.
What does it mean if your washing machine keeps beeping?
Washer sounds and beeps
Your machine is checking that the water has drained before spinning. Your washer will beep if you have used ‘No Spin’ and at the end of the cycle. If your machine is beeping continuously or giving a musical series of beeps, refer to the ‘Before you call for service’ section.
What does F9 mean on a dishwasher?
A water pressure sensor is related to the F9 fault code on Glow-Worm boilers.
What does F1 mean on a Westinghouse dishwasher?
An F1 error code on your Westinghouse dishwasher indicates that a leak is detected somewhere in the unit, whereas an F3 error code pinpoints the issue to a problem with the overflow protector. The overflow protector is normally located in the front left corner of the dishwasher tub.
What does F1 mean on Bush dishwasher?
F1 indicates water has leaked in the base of appliance and activated the anti-flood device. You will have to unplug the appliance and pull it out. Then tip it backwards by around 45 degrees so excess water drains off completely.
Where is the reset button on a Fisher and Paykel dishwasher?
Reset Procedures for the Fisher & Paykel Dishwasher
- Press and hold the button decorated with the key and lock image for five seconds.
- Press the power button to turn off power to the Fisher & Paykel dishwasher.
- Wait a few minutes and then press the power button to restore power.
How do you remove the error code on a Fisher and Paykel dishwasher?
To attempt to Clear the Fault Code
- Press to stop the beeping. Press. again to turn the dishwasher off.
- Wait a few seconds. Press. again to turn the dishwasher back on.
What does E6 mean on dishwasher?
An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.
How do I get my DishDrawer to stop beeping?
Sometimes, the beeping error on Fisher and Paykel DishDrawer Dishwasher is just abnormal, and may be fixed by simply resetting it. To do so, turn it OFF and after 10-15 minutes, turn it ON it.
What is the red light on my Fisher and Paykel dishwasher?
The red ECO light will indicate the feature is on. If your dishes are heavily soiled or you require enhanced dry performance, we do not recommend ECO programmes. If the DishDrawer® is operating and a power failure occurs, it will stop.
Why does my dishwasher stop mid cycle and beep?
If your dishwasher keeps beeping and stopping, the odds are that the door latch is loose. The reason why the dishwasher is stopping mid cycle is because the sensor on the door latch is shorted or is obscured. It could also mean that the door latch is simply broken.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do I reset my Fisher and Paykel dryer?
You can reset your dryer to the default settings it left the factory with:
- Press and hold the ‘Keylock’ and ‘Delicate’ buttons together for three seconds.
- Your dryer will now be reset to the default settings.
How do I reset my Fisher and Paykel smart drive?
How to Reset a Smart Drive Fisher & Paykel 608
- Go to the electrical outlet that you have your Fisher & Paykel Smart Drive washer plugged into. …
- Unplug the electrical cord from the wall outlet and wait 30 seconds.
- Plug the electrical cord back into the wall and turn the Smart Drive back on.
Don’t forget to share the post !