F20 Error Code
Whirlpool error code F20 appears when no water is detected entering the machine or if the pressure switch trip is not detected. The pressure switch is the part of the machine that monitors high water pressure. The washing machine automatically cancels the wash cycle during an F20 error.
similarly, How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
on the other hand, What does error code F21 mean on a Whirlpool Duet washer?
If you see error code F21 on your Whirlpool washing machine, this refers to a water drain problem. The washer won’t be able to finish the cycle and your laundry will be wet. This error code means draining is taking too long, and something is wrong with the water pumping.
also, How do you run a diagnostic on a Whirlpool Duet washer? Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)
How do you check the pressure switch on a Whirlpool Duet washer?
Use an ohmmeter to determine whether the pressure switch is malfunctioning.
- Unplug the Whirlpool Duet washer power cord from the wall outlet. …
- Go behind the Duet and remove the three screws securing the top panel to the rear panel with a Phillips-head screwdriver. …
- Locate the pressure switch inside the washer cabinet.
How do I fix a Whirlpool washer error?
If the Whirlpool washer displays the de error code on display, so there are problems with a door.
…
Manual Review
- Unplug the Whirlpool washing machine from the mains.
- Wait for 15-20 minutes while the control unit reboots.
- Reset the error by pressing the START button (On/Off).
- Check hatch locking.
Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I fix my Whirlpool F21 code?
Clogged drain into the sewer
Lint, scraps of paper, small coins, socks – anything can block the drain at the junction of the hose and the sewer hole. The solution is to disconnect the pipe and clean the drain from foreign debris that prevents water from escaping, causing the F21 error code.
How do you reset error F21?
Reset. When the “F21” error code appears, try pressing “Pause/Cancel” to stop the current wash cycle. If water remains in the washing machine tub, touch “Drain/Spin” to force a secondary drain cycle to remove the water. Once all the water drains, try selecting a new wash cycle and pushing “Start.”
How do you clear the error code on a Whirlpool front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Is there a reset button on a Whirlpool front load washer?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do you test a pressure switch?
Disconnect the wires connected to the pressure switch by pulling the wire connectors off of the switch terminals. Set a multimeter to test for resistance (ohms). Touch each tester probe to one of the switch terminals. The tester should read 0 or close to 0 (indicating no resistance).
What is E1 error in Whirlpool washing machine?
E1 – water inlet alarm
Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.
What is Fe error in Whirlpool washing machine?
The FE error code indicates that the washer is overfilling. This is usually the result of faulty water valve.
What is dE error in Whirlpool washing machine?
A dE error code indicates that the washer door was unable to lock. This can normally be resolved by performing a simple reset on the washing machine.
Why is my Whirlpool washing machine not turning on?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Where is the reset button on Whirlpool washing machine?
Is there a reset button on a Whirlpool washer? Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds.
What is the problem with Whirlpool washing machines?
The machines, branded as Hotpoint or Indesit, were sold for more than five years, but their door locking system can overheat creating the risk of fire. Owners face the prospect of doing without hot washes for months until products are fixed or replaced.
How do I fix E1 error on my Whirlpool washer?
E1 – water inlet alarm
- Check that the water faucets are not closed.
- Check that the water pressure in the house is over 20 kPa.
- Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
- Check that the drain hose is not below 27½” (700 mm) from the floor.
Where is the drain pump on a Whirlpool washing machine?
The drain pump assembly is directly in front of you, in the middle of the machine. Unscrew the knob on the drain pump by turning it counterclockwise. Hold a bucket in front of the pump while you remove the knob to catch the water. There may be as much as 2 or 3 gallons.
How do I reset my Whirlpool 360 washer?
How Do I Reset My Whirlpool Washing Machine?
- Turn off the washer.
- Turn the mode dial to NORMAL.
- Turn the dial counter-clockwise one click left, clockwise three clicks, counterclockwise one click, and then clockwise one click.
How do I clear the error on my Whirlpool Duet washer?
Press the “Pause/Cancel” button on the control panel twice to clear the error. Contact a certified repair technician if pressing the “Pause/Cancel” button does not clear the error, as this indicates that a component has failed in the washing machine or dryer.
Don’t forget to share the post !