Press the “Stop” button twice, and then press the “Power” button. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”). Press the “Start” button to complete the reset process and restart the washing machine.
similarly, How do you reset a Kenmore 500 Series washer?
How do I reset my Kenmore washer Series 500? Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
on the other hand, How do I troubleshoot my Kenmore washer?
Kenmore Washer Troubleshooting
- Bad lid switch. If your washing machine does not stop every time you open the lid, your lid switch is bad. …
- Clogged waste hose. If your washing machine does not drain the waste water, the waste hose might be clogged. …
- Bad drain pump. …
- Bad pump motor. …
- Broken drive belt. …
- Bad tub motor.
also, How do you run a diagnostic on a Kenmore washer? Close the door with the washer empty. Select “Drain/Spin” or “No Spin” by pressing the SPIN SPEED button. Within 5 seconds, push the “Prewash” option four times. The diagnostic should begin when C:00 light up.
What would cause a Kenmore washer not to spin?
If the drive belt is broken or loose, replace it. The motor coupling connects the motor to the washing machine transmission. If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission. … If the door latch is defective, the washer will not spin or start.
How do you fix a Kenmore washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do you troubleshoot a Kenmore 500 washer?
Troubleshooting Guide for a Kenmore Washer 500 Series
- Check to make sure that the washing machine is properly plugged into a grounded, three-prong electrical outlet.
- Check your fuse box or circuit breaker to make sure that the fuse is not blown or that the circuit breaker is not tripped.
How do you run a diagnostic on a Kenmore front load washer?
Here is what I did to run a diagnostic.
- With the washer empty, close the door.
- Push “control/on” or “Start”
- Select “Drain/Spin”
- Select “No Spin” by pressing SPIN SPEED touchpad.
- Push “PREWASH” option four times within 5 seconds. …
- C:00 should light up and begin the diagnostic.
What does UE mean on my Kenmore washer?
The uE and UE error codes on your Kenmore top-load washer both mean the washer won’t run the spin cycle because the load is unbalanced. … The UE error code appears if the rebalance routine fails to evenly distyribute the load after 3 attemps and the control board stops the washer.
How do I reset my Kenmore front load washer?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
What causes a washer not to agitate or spin?
The washer transmission might be worn out or defective. Transmissions have gears in them that can fail causing the washer to not spin or agitate. … If the motor is turning the transmission, but the washer won’t spin or agitate, consider replacing the transmission.
Why does my washer not spin all the water out?
If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Check these areas and remove anything that may be clogging the draining system on your washer.
How do you force a washer to drain?
How to Manually Drain a Top-Loading Washing Machine
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose at the back of the washing machine. …
- Step 3: Drain the water. …
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose. …
- Step 3: Drain the water. …
- Step 4: Scrub the filter.
What causes a washer to not spin out all the water?
If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Check these areas and remove anything that may be clogging the draining system on your washer.
Why does my Kenmore washer take so long to wash?
A washer that continuously takes too long to wash may have a malfunctioning load sense system, or greater problems with its control panel. There may also be issues with your water inlet valve, which pulls water into the appliance for each cycle.
How do you clean the lint trap on a Kenmore washer?
How to Clean the Lint Trap in a Kenmore Washing Machine
- Lift up the lid to your Kenmore washing machine.
- Twist off the top of the agitator, the bar in the center of the machine that moves the laundry around.
- Pull out the plastic lint trap. …
- Screw the agitator’s top back on.
How do I reset my Kenmore 417 washer?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
How do you calibrate a Kenmore washing machine?
- Power off, and then power on the washing machine.
- Hold down Temp. and Delay End+ simultaneously for 3 seconds to enter Calibration mode.
- Press and hold Start/Pause (Hold to Start) to run the Calibration cycle.
- When the cycle is complete, “0” appears on the display and the washing machine will turn off automatically.
What does it mean when your washer says UE?
The uE/UE code indicates that the washer is attempting to balance the load, which may be the result of the unit not being leveled correctly or the load itself. This code can be easily resolved without the need of a technician.
How do I make my Kenmore washer spin only?
7 Answers from these members:
- TURN THE POWER BUTTON ON, PUSH THE SPIN SPEED BUTTON NEXT TO DESIRED LEVEL, THEN PRESS START, THERE YOU GO , IT WILL ONLY SPIN, NOT RINSE AND SPIN – Worked for me on my Kenmore Elite. …
- I have a Kenmore series 600 top loader that has been nothing but problems since day.
Why is my front-load washer always off balance?
Laundry caught below the tub or between the agitator and the inner tub can cause the washer to operate off balance with every load. The problem can be anything: a penny that worked its way out of a pocket, a button that fell off a shirt or a wayward sock or other article of clothing.
How do I fix the error on my Kenmore Elite washer?
Kenmore front-load washer LE error code
- Overloaded washer. Make sure the washer isn’t overloaded. …
- Too much detergent. If you see lots of suds in the tub, let the washer sit idle for 30 minutes so the foam dissipates. …
- Drive system obstruction. …
- Loose wiring or defective drive motor.
How do you reset a front loader washing machine?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
Don’t forget to share the post !