Troubleshooting a Maytag Dryer Not Starting
- Test the outlet: Make sure the dryer is properly plugged into a functioning outlet. …
- Check for blown fuses or tripped breakers: Reset any tripped breakers or replace broken fuses.
similarly, What does f3 mean on Maytag dryer?
F3E2 – Moisture Sensor
The F3E2 error code occurs when five consecutive loads are dried without registering moisture sensor data. Pressing the ‘Power’ button will clear the error code and allow you to restart the machine. If the problem persists, call for service.
on the other hand, When I press the start button on my dryer nothing happens?
If your dryer won’t start when you push the start button, the most likely causes are a lack of power, a defective door switch, a blown thermal fuse or a bad start switch. … If it doesn’t turn on, it’s likely that the dryer has no power. Check your power cord and the house circuit breaker.
also, What do you do when your Maytag dryer won’t start? Make sure both fuses are intact and tight, or that either circuit breaker has not tripped. You can test the breaker by turning the breaker off and then back on. Replace the fuse(s) or reset the circuit breaker(s). If the problem continues, call an electrician.
Why would a Maytag dryer not start?
If your Maytag dryer won’t start, just clicks, and multimeter testing of the fuse reveals no continuity, it’s either blown or defective. In both cases, the fuse can’t be repaired and must be replaced. Even if you don’t suspect overheating, a blown thermal fuse warrants a dryer vent inspection.
What does E2 mean on dryer?
The Whirlpool Duet Dryer Error E2 means the control has detected that the thermistor is shorted. This error can be a wiring issue from the control to the thermistor or a bad thermistor. In some cases it can be a bad control reporting false errors but this is not common.
Where is the moisture sensor in a Maytag dryer?
It’s typically found on the back wall of the dryer drum or in the front near the lint trap. Use fine grit sandpaper to scrub the moisture sensor. This will help remove fabric softener build-up, lint, or any debris that is interfering with the sensor.
Where is the reset button on a dryer?
Many dryers are equipped with a reset button on the control panel. If the motor won’t run, let the dryer cool for about ten minutes.
How do I know if my thermal fuse is blown?
How to tell if a thermal fuse has blown? To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
What would cause a dryer to not turn on?
Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board:
- Problems with the door switch can prevent the dryer from starting. …
- A blown thermal fuse often prevents an electric dryer from starting.
How do you unlock a Maytag front load dryer?
Press and hold the Control Lock Key for 3 seconds to unlock the machine. You will notice the machine count down from 3-2-1. The control lock may be a stand alone key, or it could be a dual function key paired with another button like Extra Rinse, Steam, etc.
Where is the thermal fuse on a Maytag front load dryer?
This fuse is located on the exhaust duct. If the dryer overheats, the thermal fuse opens to cut off power to the dryer. The thermal fuse cannot be reset–if the thermal fuse is open, it must be replaced.
How long should Maytag dryer last?
A dryer should last 10-13 years. To extend the dryer’s life, clean the lint trap after each use and make sure the outer vent is clear as well.
What does E2 F3 mean on Whirlpool dryer?
The F3E2 Error Code indicates that there may be an issue with the Temperature Control sensor. Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
What does F5 and E2 mean on a washing machine?
The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area. Also verify there are no clothing items in the way.
What does F3 mean on my Whirlpool dryer?
The “F3” fault code is displayed because the dryer is not heating. The first thing to check and verify is the voltage supply. The dryer must have 220 volts or it will run but not heat. If the dryer is getting the correct voltage then I would disconnect the power cord and then remove the top panel.
How do you know if your dryer sensor is bad?
If your Whirlpool dryer leaves clothes damp, you may have a defective moisture sensor. A common symptom of a failed sensor is a Whirlpool dryer not drying all the way. The dryer moisture sensor is designed to detect the moisture level in the dryer and adjust the dry cycle time accordingly.
Why is my dryer running but not heating?
Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element. If you gather your tools and follow this guide, you may be able to solve basic dryer heating problems on your own.
How do I reset my thermal fuse?
- Step 1: Locate the Fuse. Study the owner’s manual for the location of the thermal fuse. …
- Step 2: Cut Power to the Dryer. …
- Step 3: Disassemble as Needed. …
- Step 4: Disconnect the Thermal Fuse. …
- Step 5: Conduct a Continuity Test. …
- Step 6: Purchase a Replacement. …
- Step 7: Replace the Fuse. …
- Step 8: Reassemble the Dryer and Test It.
Can I bypass thermal fuse on dryer?
If you do not have access to a multimeter or ohmmeter, you can momentarily bypass the thermal fuse. … Operating a dryer with a bypassed thermal fuse is both unnecessary and unsafe, so a bypass should only be done long enough to troubleshoot a potential problem.
How do you tell if a thermal fuse is blown without a multimeter?
Testing By Bypassing The Fuse
If you do not have a multimeter, you can also test whether or not the fuse is working by bypassing the fuse itself. Simply detach the wires from the fuse, wire them together using a jumper wire and attempt to operate the dryer.
How do you unclog a dryer vent?
How to clean your dryer vent in 6 easy steps
- Step 1: Find your vent. Before you can clean your dryer vent, you’ll need to figure out where it actually is. …
- Step 2: Carefully disconnect your dryer. …
- Step 3: Vacuum the lint. …
- Step 4: Get in there with a brush. …
- Step 5: Clean up and reconnect. …
- Step 6: Celebrate.
Can I fix my dryer myself?
Here’s the first thing to know about dryer repair: You can solve most dryer troubles yourself. There’s no need to find a technician, schedule a service call or pay hundreds dollars for dryer repair.
Don’t forget to share the post !
