A DC code error on a Samsung washing machine indicates that the washer is unable to spin due to a load imbalance. Correcting a DC error is as simple as redistributing the weight of an existing load, removing items to reduce the overall weight in the washer, or changing suspension rods (or shock absorbers).
similarly, How do I fix the OE code on my Samsung washer?
Lots of detergents or the wrong detergent is used
And the OE code appears on the display of the Samsung washing machine. To eliminate the false overflow error due to foam, turn on the spin mode to drain the water completely, remove the laundry and run the machine in rinse mode to rinse the drum.
on the other hand, Why does my Samsung washer keep saying DC?
A dc error code on your Samsung front-load washer means the washer won’t spin because the load is unbalanced. Fixing a dc error code can be as easy as redistributing an unbalanced load or adding a few garments to a small or single-item load.
also, Why is my Samsung washer always unbalanced? The drum is overloaded or underloaded. If you wash your laundry at a temperature of more than 60 degrees, some extra water enters the washer during the rinse cycle. This may lead to a slight imbalance. … If the bearings are worn or rusty or the shaft is bent, the vibration increases and the washer may not spin at all.
How do I fix error code OE?
OE can be triggered by a kinked drain hose or a clogged drain pump filter.
- Check for kinked drain hose. Check behind the washer to ensure that the drain hose is not kinked or clogged. …
- Test the drain pump. …
- Do you hear the humming sound? …
- Clean drain pump filter. …
- Run tub clean cycle. …
- Request Repair.
How do I know if my washing machine drain pump is bad?
How do I know if my washing machine water pump is bad?
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle.
- Wait for the washer to finish its cycle.
What is IE error in Samsung washing machine?
Samsung malfunction 1E or 1C
Is there an error message 1E or 1C on the display of your Samsung washing machine? If so, there is a problem with the water level sensor. This means that the water pressure or water level is not correct.
How do I get my Samsung washer to spin only?
To run a Spin Only cycle on a model that does not have this option on the cycle selector dial, perform the following:
- Power the unit on.
- Press and hold the spin key for approximately 3 seconds. A chime will sound.
- Select the spin level, if desired.
- Press the Start/Pause button.
Is there a reset button on my Samsung washer?
To reset your Samsung washing machine you need to simply disconnect the washing machine from power for 5 to 10 minutes. … Once the 5 to 10 minutes has passed, connect power to your Samsung washer and run a test wash load to see if the error code has cleared.
Why does my washer keep going off balance?
Laundry caught below the tub or between the agitator and the inner tub can cause the washer to operate off balance with every load. The problem can be anything: a penny that worked its way out of a pocket, a button that fell off a shirt or a wayward sock or other article of clothing.
How do you balance Samsung washer?
- 1 Tap Settings on your washing machines display.
- Tap Calibration.
- Tap Start. The washing machine door will lock and the drum will rotate clockwise and anticlockwise for several minutes. When your washing machine has finished calibrating, it will turn off automatically.
Why does my washer get unbalanced?
If a suspension rod is broken, replace it. One or more of the suspension springs might be broken. The suspension springs help to absorb the movement of the washer tub. If a suspension spring breaks, the tub might become unbalanced, causing it to shake and vibrate during operation.
What does oe mean?
Original equipment parts (OE parts) are parts installed when a finished product or sub-assembly is manufactured.
How do I clear my washing machine drain pipe?
To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.
How do you check a washing machine drain pipe?
To test this, remove the drain hose attached to the washer and make sure it is clear. An easy way to check that the drain hose is clear is to blow air through it. If nothing is obstructing the drain tube, the problem is most likely at the washing machine pump.
How do you empty a washing machine full of water?
5 Easy Steps to Get Water Out of Your Washer
- Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. …
- Step 2: See If You Can Drain the Drain Hose. …
- Step 3: Check Out the Drain Pump. …
- Step 4: Drain the Interior Manually If Needed. …
- Step 5: Know When to Call a Professional.
What causes a washing machine pump to break?
Sometimes a damaged impeller or a defective seal can cause a mechanical failure in the pump. Additionally, if the pump operates with its own motor, it could experience electronic failure. You can confirm the functionality of the drain pump with a multimeter.
Why does my washer keep saying IE?
An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen.
Why is my Samsung washer blinking?
Samsung washer spin light blinking
For the most part, this is due to improper installation of the washer or failing to balance the load. For that reason, work on balancing the load size (as explained earlier) and ensure the selected type of cycle matches what you’re washing.
Why is my washer not spinning all the water out of my clothes?
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already. … If the visual inspection checks out, you will want to remove the washer drain hose.
How do I get my washer to spin only?
- To perform a spin only cycle: Press the power button to turn the washer on. Press and hold the spin button for 3 seconds. …
- Yes, hold spin only at center bottom of key pad. Has asterisk next to it. …
- Press spécial care then spin only. …
- Spin towels. …
- Press on then special care then spin only. …
- Just put it on spin, and it will.
How do you troubleshoot a Samsung washing machine?
Troubleshooting
- Unplug the machine. …
- Disconnect the hoses.
- Remove the detergent drawer by pressing the central locking button.
- Open the hatch of the drain filter at the bottom of the front panel.
- Empty the water and clean the filter.
- Put the washer on a side so that you can access the bottom.
Where is the reset button on my Samsung dishwasher?
Unlike their other appliances, Samsung dishwashers tend not to have a reset button or functionally.
…
How to Fix a Samsung Dishwasher That Won’t Turn On
- The power button does not respond when you touch it. …
- The circuit breaker has a tripped circuit. …
- The switch near the dishwasher is off.
How do I fix my Samsung washer?
Occasionally, the UR error code is caused by a fault with the electronic controller, which has mistakenly identified an unbalanced load error when there is none. Resetting the washer by disconnecting the power to the washer for 10 minutes should fix the issue.
Don’t forget to share the post !