Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds. Press the Pause / Cancel / Stop button twice to clear the display.
similarly, How do I run diagnostics on my Kenmore Elite washer?
Select “Drain/Spin” or “No Spin” by pressing the SPIN SPEED button. Within 5 seconds, push the “Prewash” option four times. The diagnostic should begin when C:00 light up.
on the other hand, Why is my Kenmore washer not turning on?
First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. … To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
also, How do I reset my Kenmore top load washer? To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
How do I clear the error code on my Kenmore washer?
You will need to remove the power supply to the washer to reset the code.
- Look for the “Pause/Cancel” button on the washer control panel. …
- Press the “Pause/Cancel” button twice to cancel the wash cycle. …
- Connect the water supply hoses back to the washer and turn on the water spigots.
What does F mean on my Kenmore Elite washer?
The F indicates that the washer control detected a component problem. … If the F code was caused by excessive suds preventing the washer from draining, you may be able to shut the door and run a drain/spin cycle to remove the water from the washer.
What does IE mean on a Kenmore Elite washer?
The IE code indicates that the washer detects a problem with water fill. Make sure that the hot and cold water supply faucets behind the washer are fully open.
How do you fix a washer that won’t start?
How to Fix a Washing Machine That Won’t Start
- Activate the power button.
- Test the outlet.
- Reset outlet if necessary.
- Make sure the power cord is plugged in.
- Check if fuses are blown or the circuit breaker is thrown.
- See if Delay Start has been pushed.
- See if Control Lock has been activated.
Does a Kenmore washer have a fuse?
Your washer does NOT have a fuse in it. … Unplug the washer and plug in a hair dryer to see if the outlet works. If the hair dryer doesn’t operate check and reset the circuit breaker inside your circuit breaker box and then see if the washer or hair dryer operates.
Why did my washer just stopped working?
There are a number of possible causes for your washing machine not working as it should. … Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining.
Why does my Kenmore washer take so long to wash?
A washer that continuously takes too long to wash may have a malfunctioning load sense system, or greater problems with its control panel. There may also be issues with your water inlet valve, which pulls water into the appliance for each cycle.
Why won’t my washer go past the wash cycle?
The reason a washer won’t move to the next cycle depends on the kind of washer you have: … A washing machine that won’t finish the cycle could also have a broken timer or failed water-level pressure switch.
Is there a reset button on a washer?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do I reset the F5 on my Kenmore washer?
It goes through the wash cycle and then ends with an F5 error and recurring beeping alarm. The “lid locked” LED flashes as well. The only way to clear the codes is to unplug and let sit, and then plug back in.
What does F mean on Kenmore Elite washer?
The F indicates that the washer control detected a component problem. … If the F code was caused by excessive suds preventing the washer from draining, you may be able to shut the door and run a drain/spin cycle to remove the water from the washer.
How do I troubleshoot my Kenmore washer?
Kenmore Washer Troubleshooting
- Bad lid switch. If your washing machine does not stop every time you open the lid, your lid switch is bad. …
- Clogged waste hose. If your washing machine does not drain the waste water, the waste hose might be clogged. …
- Bad drain pump. …
- Bad pump motor. …
- Broken drive belt. …
- Bad tub motor.
How do I fix the Sud error on my Kenmore Elite washer?
This is often caused by too much detergent being used or non HE detergent being used in an HE machine. Run the machine through a Rinse/Spin cold water cycle then a Normal cycle without adding any additional soap. This will remove as much remaining soap held in the fabric.
How do you reset a Kenmore 500 Series washer?
How do I reset my Kenmore washer Series 500? Top Load Washer – Hydrowave Motor Reset Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
What does uE mean on Kenmore washer?
The uE error code appears when the washer’s electronic control board detects the unbalanced load and tries to correct the imbalance by adding water and agitating the laundry to distribute garments evenly in the spin basket.
What does IE mean on a washer?
An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen.
How do I fix Internet Explorer error on my Kenmore Elite washer?
ERROR CODE IE Inlet water supply error
Check the water supply faucets behind the washer to make sure they are fully open. Check the fill hoses for kinks or freezing (in winter). Check the inlet water valves. If the valves are defective, replace the inlet water valve assembly.
How do I reset my Kenmore front load washer?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
Why is my Kenmore washer stuck on sensing?
A Kenmore washer that’s not working, won’t cycle, or keeps sensing likely has a defective timer, lid switch, line fuse, user-control display board, door lock, or water inlet valve. Users can temporarily resolve the issue with a master reset or by manually shifting the washer to the next cycle.
Don’t forget to share the post !