CL Error Code
It is an indicator that the child lock feature is set active. When the child lock feature is active, the control panel will be disabled and settings cannot be adjusted. To fix this: Press and hold the child lock button for 3 seconds.
similarly, How dO I turn off child lock?
- You can activate the CHILD LOCK function by pressing the STOP button for more than 5 seconds. The key symbol will light up in the front panel display.
- To cancel, press the STOP button for more than 5 seconds so that the key symbol disappears from the front panel display.
on the other hand, Why is my washing machine blinking CL?
The “rL” error code means that a load has been detected in drum during Clean Washer with affresh® cycle. The Clean Washer cycle is meant to run empty, with no clothing inside the washer. Remove items from washer drum and restart Clean Washer with affresh® cycle.
also, How do I find the error code on my Whirlpool washer? The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time. To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.
Is there a reset button on the Whirlpool washer?
Is there a reset button on a Whirlpool washer? Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds.
What does LC mean on Whirlpool dryer?
If you see the “LOC”, “lc” or “LC” code on the control, the control lock has been set. Disconnect the control lock setting. If you are unsure of how to disconnect the control lock for your model, see your Owner’s Manual.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do you reset a front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do I fix the code on my Cabrio washer?
Simply put, too much detergent was used and an excessive amount of suds or foam was produced. Adding an additional rinse cycle without adding any more detergent might fix this problem. Sometimes the machine will automatically detects this problem and add a pause and additional rinse cycle in order to break up the suds.
Do washing machines have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do you reset the code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I reset the lid lock on my Whirlpool washer?
If your lid lock light is flashing, you can unplug your washer for 10 minutes and plug it back in to reset the washer and the flashing light. You can also press and hold the ‘End of Cycle’ button for 20 seconds to reset the washer and flashing lid lock light.
Where is the Control Lock on Whirlpool dryer?
Locate the “Control Lock” button, which is often located on the right side of the control panel of Whirlpool Duet models.
What do you mean by LC in washing machine?
An LC error code indicates a leak. … The washing machine includes draining for 3 minutes so that the contents of the drum do not leak into the electronic components. An LC error code appears on display.
What does it mean when dryer says Loc?
1 Answer. @divorcedhelp the “LOC” indicates the (Control Lock). This means the control panel has been locked and it will have to be unlocked before you can use the dryer. To unlock the control panel; press and release the Option and Select buttons at the same time.
How do I reset the lid lock on my GE washer?
Top Load Washer – Lid Lock Feature
- Make sure the washer is paused (press Start/Pause). During spin, this can take up to 3 minutes for the basket to stop spinning and allow you to open the lid.
- Unplug the washer for a minute to reset.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
How do you reset a front load GE washer?
How do you reset a front load GE washer?
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do you reset the code on a Whirlpool Cabrio?
How do you clear the codes on a Whirlpool Cabrio?
- Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
- Choose a new cycle and press “Start” to begin.
- Turn off and disconnect the Cabrio if the error or problem persists.
- Wait several minutes before restoring power.
How do I know if my detergent is high efficiency?
Walk down the laundry detergent aisle in any store, and almost every single bottle, box, and the bag has a little symbol on the label: the letters “h” and “e” separated by a red dot on a field of blue surrounded by a white circle swirl. The HE stands for high-efficiency laundry detergent.
How do you reset the code on a washing machine?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do I troubleshoot my LG washer?
How to troubleshoot:
- Open the stop valve to its full capacity. It may be closed or opened insufficiently.
- Check the intake hose. …
- The filter screen may be clogged with debris as well. …
- The intake valve is malfunctioning. …
- If the pressure switch is broken, you can repair your LG washing machine yourself.
How do you reset the code on a Maytag Centennial washing machine?
To exit the Maytag Centennial diagnostics press and hold the “start” button for about 3 seconds. (Again… This will erase error codes in the Centennial washer’s memory.) Now you can do run a Maytag Centennial automatic diagnostic washer cycle.
What does the code CL mean on my Maytag washer?
Does the washer need to be cleaned? The CL code is a reminder to run the Clean Washer cycle and will appear after 30 cycles. The code will automatically clear once a Clean Washer cycle has completed or after three cycles.
Don’t forget to share the post !