Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.
similarly, How do I fix Fisher and Paykel dishwasher f1 error?
- Locate the drain-access filter panel on the bottom of the drawer.
- Remove the rack that sits above it.
- Pull up to lift the drain filter and remove it from the machine.
- Set the filter under the faucet to rinse it clean with cold water.
- Reinstall the filter and confirm that it sits flush with the bottom of the DishDrawer.
on the other hand, How do I fix E6 error on Fisher and Paykel dishwasher?
Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.
also, How do I fix the f2 on my Fisher and Paykel dishwasher? Reset Procedures for the Fisher & Paykel Dishwasher
Press the power button to turn off power to the Fisher & Paykel dishwasher. Wait a few minutes and then press the power button to restore power. Turn off and unplug the dishwasher if the issue remains.
Why is my Dishdrawer beeping?
The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. Press ► once to stop the beeping, and then again to clear the fault. / ► to resume the wash program.
What does F9 mean on a dishwasher?
A water pressure sensor is related to the F9 fault code on Glow-Worm boilers.
How do I fix E6 error on my dishwasher?
Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.
How do I reset my Fisher and Paykel washing machine?
Factory Reset
- Turn the dial to select ‘Spin’.
- Touch and hold the ‘Delay Start’ ‘More’ , the ‘Delay Start’ ‘Less’ and ‘Options’ buttons together for 3 seconds will appear on the screen and the machine will beep.
- Your washer will now be reset to the default settings.
What does E6 mean on dishwasher?
An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.
What does E4 mean on a dishwasher?
Error message E4 in free-standing compact dishwasher indicates too much inlet water and/or a leak.
What does F2 mean on a dishwasher?
If your dishwasher doesn’t drain properly, you’ll see standing water on the bottom of the dishwasher when the cycle is complete and the error code F2 may be displayed.
What does E2 mean on a dishwasher?
E2 – Abnormally long drain time. Check to make sure that the drain line is not obstructed or bent in a way that restricts water flow. Make sure the drain line is routed below the height of the dishwasher and that it has not been extended. This will inhibit the ability of the drain function to operate properly.
How do I get my DishDrawer to stop beeping?
Sometimes, the beeping error on Fisher and Paykel DishDrawer Dishwasher is just abnormal, and may be fixed by simply resetting it. To do so, turn it OFF and after 10-15 minutes, turn it ON it.
Why is my Elba dishwasher beeping?
Blinking lights and beeping sounds can be caused from a power surge. So its beeping and flashing once per second correct this beeping and flashing is an error code that your unit is giving blinking lights or beeping sounds may indicate a problem with the dishwasher caused by power surges.
How do I fix error e1 F9 on Maytag washer?
Possible Solutions
Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. Also make sure that the drain hose end is higher than 36 inches from the floor.
How do I clear the error code on my KitchenAid dishwasher?
Control Panel Reset
When powering down the unit and turning it back on doesn’t work, it may be best to reset the control panel’s computer. This is done by pressing two buttons, one after the other, at least five times each for a total of 10 presses. The door must be completely shut while the buttons are being pressed.
What does f2 mean on sharp dishwasher?
This error message means that you have a leak under the floor pan. Please check the machine for leaks. At the bottom there is a float switch that triggers the Aqua stop in the event of a leak. Either you have to open the rectangular cover below the door to check.
What does E6 mean on my dishwasher?
An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.
Where is the flood switch on a dishwasher?
The anti flood switch is in the bottom of the bas of the dishwasher. If its activated try and pull the dishwasher out and tip it 45 degs backwards and the water should drain out from the base and that way the flood switch will reset itself.
How do I fix E5 error on my dishwasher?
1. Switch the power off and restart the dishwasher
- To do this you need to press the on/off button on the machine.
- When you have clicked the button wait a few minutes.
- Restart the dishwasher using the same button.
How do you troubleshoot a Fisher Paykel washing machine?
How to Troubleshoot Fisher Paykel Washers
- Check the hot water light. …
- Check the cold water light. …
- Check both the hot and cold water lights. …
- Check the high water light. …
- Look at the first rinse light and spin light. …
- Examine the lid-lock light. …
- Look at the first rinse light, the spin light and the spin speed light.
How do I reset my Fisher and Paykel wa1068g1 washer?
You can reset your washer to the settings it left the factory with:
- Enter Option Adjustment mode (refer to ‘Option Adjustment’).
- Select the ALLERGY cycle.
- The display will show “rSt”. Touch and hold START / PAUSE for 3 seconds to reset your washer to its factory settings.
How long does a dishwasher last?
A typical dishwasher should last about 10 years, according to Consumer Reports.
How do I fix e5 error on my dishwasher?
1. Switch the power off and restart the dishwasher
- To do this you need to press the on/off button on the machine.
- When you have clicked the button wait a few minutes.
- Restart the dishwasher using the same button.
Don’t forget to share the post !