A DC code error on a Samsung washing machine indicates that the washer is unable to spin due to a load imbalance. Correcting a DC error is as simple as redistributing the weight of an existing load, removing items to reduce the overall weight in the washer, or changing suspension rods (or shock absorbers).
similarly, How do I get rid of DC error on my Samsung washing machine?
Front Loader: Washing machine displays a UE or DC Error Code
- 1 Turn off and unplug the unit from the power outlet.
- 2 Check the Shipping Bolts (Make sure they have been removed)
- 3 Check if the Washing Machine is installed on a level ground.
- 5 Open the door, take out the clothes, put them back in, and then close the door.
on the other hand, How do I get my Samsung washer to spin only?
To run a Spin Only cycle on a model that does not have this option on the cycle selector dial, perform the following:
- Power the unit on.
- Press and hold the spin key for approximately 3 seconds. A chime will sound.
- Select the spin level, if desired.
- Press the Start/Pause button.
also, Is there a reset button on my Samsung washer? To reset your Samsung washing machine you need to simply disconnect the washing machine from power for 5 to 10 minutes. … Once the 5 to 10 minutes has passed, connect power to your Samsung washer and run a test wash load to see if the error code has cleared.
What does the red lock mean on Samsung washing machine?
If you see a key indicator rather than a lock, this means that the door is locked. This may be because the child lock is on but may also be because the cycle is not finished or the machine has detected an error.
What are the codes on a Samsung washer?
Samsung Front-Load Washer Fault Codes
| Fault Code | Washer Problem |
|---|---|
| LE | Low water level during cycles |
| OE | Overflow or too high water levels |
| nF1 | Hot and cold water lines are reversed |
| tE | Water temperature is either too high or too low |
• 28 juin 2021
What causes a Samsung washer not to spin?
If your Samsung washing machine does not spin fully or at all during the rinsing or spinning phase of the cycle it is most likely to be caused by an unbalanced load. … 1 Open the door and redistribute the washing more evenly around the drum. 2 Check that the drum is not over or under loaded.
Why is my washer not spinning all the water out of my clothes?
Drain Hose Issues
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already.
How do I get my washer to spin only?
- To perform a spin only cycle: Press the power button to turn the washer on. Press and hold the spin button for 3 seconds. …
- Yes, hold spin only at center bottom of key pad. Has asterisk next to it. …
- Press spécial care then spin only. …
- Spin towels. …
- Press on then special care then spin only. …
- Just put it on spin, and it will.
Where is the reset button on my Samsung dishwasher?
Unlike their other appliances, Samsung dishwashers tend not to have a reset button or functionally.
…
How to Fix a Samsung Dishwasher That Won’t Turn On
- The power button does not respond when you touch it. …
- The circuit breaker has a tripped circuit. …
- The switch near the dishwasher is off.
How do you troubleshoot a Samsung washing machine?
Troubleshooting
- Unplug the machine. …
- Disconnect the hoses.
- Remove the detergent drawer by pressing the central locking button.
- Open the hatch of the drain filter at the bottom of the front panel.
- Empty the water and clean the filter.
- Put the washer on a side so that you can access the bottom.
How do I fix my Samsung washer?
Occasionally, the UR error code is caused by a fault with the electronic controller, which has mistakenly identified an unbalanced load error when there is none. Resetting the washer by disconnecting the power to the washer for 10 minutes should fix the issue.
How do you bypass the lid lock on a Samsung washer?
How to Bypass a Washing Machine Lid Lock
- Turn off the washer and unplug the appliance. …
- Locate the retaining tabs and/or screws that hold the top horizontal panel down. …
- Look for the lid lock switch on the underside of the top panel and where it fits into the appliance.
How do I troubleshoot my Samsung washer?
Troubleshooting
- Unplug the machine. …
- Disconnect the hoses.
- Remove the detergent drawer by pressing the central locking button.
- Open the hatch of the drain filter at the bottom of the front panel.
- Empty the water and clean the filter.
- Put the washer on a side so that you can access the bottom.
What does key lock mean on a washing machine?
The Key Lock mode disables the control panel so that the storage environment cannot accidentally be changed. The display will automatically lock after 15 seconds of the display not being used or when the drawer is closed.
How do I fix the SC code on my Samsung washer?
The 5C or SC error is caused by major debris. Common culprits are usually accumulated debris, as well as piled up socks. To fix this error, you have to remove the clogs, wash the filter, and then reinstall the filter.
What causes a front-load washer not to spin?
Front-load washer tubs spin thanks to a drive belt that runs off of the motor. A loose, frayed, or torn belt could be why your washer won’t spin. Overloading your washing machine can cause the belt to loosen or become worn out. Inspect the drive belt closely.
What do you do if your Samsung washer won’t drain?
More videos on YouTube
- Turn off the washer and check the level. If the washer isn’t level it may not drain correctly. …
- Inspect the drain hose. …
- Clean the pump filter (front loaders only). …
- Turn the washer back on and start a cycle.
Why do I have to spin my washer twice?
– Check the drain pump debris filter or coin trap, objects may be blocking the water flow. – Check inside drain pump and all hoses connected to drain pump for foreign debris or small pieces of clothing. – Be sure the wash load of clothing is balanced, balance out the wash load if you see all clothing to one side.
Can you do just a spin cycle on LG front load washer?
The spin only feature on your top load washer can be activated by pressing the Special Use selection button. Choose only spin.
Does Spin Cycle drain water?
It removes the water from the tub during the spin cycle. The washer pump forces water from the bottom of the machine into the drain hose. The drain hose loops to the top of the machine, and then down to the drain, enabling the tub to fill. When the water reaches the bend in the hose, it goes out of the drain.
What is the difference between rinse and spin and drain and spin?
Rinse: The dirty, soapy water is drained, then the washing machine is refilled and your clothes are “rewashed” in clean water. Spin: All the water is drained completely, then your clothes are spun very fast and excess water is removed thanks to centrifugal force.
Why are the lights on my Samsung dishwasher flashing?
This means there is too much water in the dishwasher. This is often related to a drain issue. Inspect the dishwasher’s drain connection at the sink. Check the drain hose.
Is there a way to reset a dishwasher?
Try pressing the “Start/Reset” pad to reset the dishwasher and wait 2 minutes. If the problem persists, reset (reboot) the dishwasher by turning off power to the unit at the house circuit breaker or fuse box for 30 seconds. Restore power and the dishwasher should reset and function normally.
How do I reset the error code LC on my Samsung dishwasher?
Quick answer: The LC flashing on your Samsung dishwasher indicates that the leak sensor in the dishwasher detects a water leak or moisture. To clear the error code LC, simply remove power to the dishwasher for 15 minutes. This should reset the dishwasher and clear the error code.
Don’t forget to share the post !
