As long as there are no sharp edges in the chase that might physically damage the cable, there’s no code violation if Romex touches metal hvac supply or return ducts. … Metal chimneys and other combustion vents are a different matter, however, since they have necessary clearances that must be maintained.
similarly, What type of dryer vent hose is best?
Venting Guidelines
- All dryer ducting must be a minimum of 4″ in diameter. …
- Flexible transition hose between the dryer and the wall outlet should be either the foil type or the aluminum flexible duct (most preferred). …
- Concealed ducting must be rigid metal (galvanized or aluminum) duct.
on the other hand, Can PEX touch dryer vent?
2) Dryer installation instructions typically prohibit contact with combustible materials. So PEX less than 6“ from a dryer exhaust falls in a gray area somewhere between these requirements.
also, Can dryer vent touch wall? For a residential clothes dryer exhaust vent using materials and routing approved by the manufacturer you would not have an issue with the vent touching or being close to drywall.
Can dryer vent touch water lines?
yes….. yes.
Can a dryer vent hose be too short?
No. You must have a back draft damper (you can find these at any home center) at the end of the exhaust. You would then attach your dryer venting apparatus to the damper assembly. If you where planning on running flexible duct through the wall that is also a code violation.
Can a dryer vent go up through the roof?
It is not advisable to vent a dryer through the roof. This is one of the most common mistakes we see from people who are not experienced with air ducts. Dryer vent specialists will tell you that a vertical approach to installing a dryer vent is inefficient and creates a fire risk for a home if it goes unchecked.
Can you run hot and cold PEX side by side?
Hot and cold PEX water lines run through the same hole in a stud wall. … This is not a typical installation; both pipes should have their own holes to pass through the framing.
Can a dryer duct touch wood?
Yes, that is considered safe. Direct wood contact is not a problem with the operating temperature of a dryer vent. You’ll have no fire if the vent is clear. lint does not escape from the pipe if all joints are foil taped.
Can you run PEX all the way to water heater?
Can I Connect PEX to My Water Heater? PEX can’t be directly connected to a water heater.
How hot is dryer vent?
The exhaust temperature of a dryer can vary from 50 to 71C (120 to 160F), though there is a chance if the dryer is broken that it could be higher.
Why would dryer be wet inside?
Heavy items made of cotton hold more moisture that can collect in the dryer. … Condensation usually results from improper ventilation, which can cause moisture and lint to collect in the dryer’s exhaust system duct and leak back into the dryer after it turns off.
Why is dryer vent full of water?
Hot, humid air passes from the dryer through the exhaust vent hose to the outside. … Over time, this debris can build up inside the exhaust vent, eventually preventing hot air from escaping. As a result, that warm, moist air remains inside the vent tube—and gradually turns into condensation as it cools.
Why is my dryer leaking water underneath?
Blocked ventilation is often the reason why a dryer is leaking water. … It is recommended that the dryer’s ventilation system be cleaned at least once a year to avoid blockages. Disconnecting the ventilation hose from the dryer and cleaning out this area can solve the problem.
How often should a dryer vent be cleaned?
A good rule of thumb is to have your dryer exhaust vents inspected and cleaned by a professional at least once per year. However, if you have a household that uses your dryer often, such as one with a lot of children, you may want to consider increasing that amount to every six months.
Can you cut dryer vent duct?
Shortening your dryer vent can increase the efficiency of your clothes dryer, lengthening its lifespan and saving you a little on your utility bills. It also reduces the chance of lint build-up in the vent causing a fire.
Does length of dryer vent matter?
A dryer vent should not exceed 35 feet in length. Furthermore, for every 45 degree turn of a dryer vent you should remove 2.5 feet in total allotted length. For every 90 degree turn, you should remove 5 feet in total allotted length.
How do you clean a dryer vent pipe?
How to clean your dryer vent in 6 easy steps
- Step 1: Find your vent. Before you can clean your dryer vent, you’ll need to figure out where it actually is. …
- Step 2: Carefully disconnect your dryer. …
- Step 3: Vacuum the lint. …
- Step 4: Get in there with a brush. …
- Step 5: Clean up and reconnect. …
- Step 6: Celebrate.
Can you run a dryer vent vertical?
DEAR BOB: A vertical dryer vent is typically a problem because it acts as a moisture condenser. The sheet metal duct is cooled by the outside air in the attic. This causes the steam from your dryer to become liquid on the inner surface of the duct. … Unfortunately, a horizontal vent duct is not required by code.
Can a dryer vent go into garage?
If you have a gas-fired dryer, it’s not only a bad idea to vent it into your garage, it’s potentially deadly. Gas-fired dryers eject small amounts of carbon monoxide, and it’s critical that they’re properly vented to the outdoors. … Dryer vents should be as straight as possible and not exceed 35 feet in length.
Can a dryer vent touch wood?
Yes, that is considered safe. Direct wood contact is not a problem with the operating temperature of a dryer vent. You’ll have no fire if the vent is clear.
Can a gas dryer vent touch wood?
Yes, that’s considered safe. The operating temperature of a dryer vent is not a problem for direct wood contact. Keep the vent clear and you’ll have no fire. Ensure all joints are foil taped, so lint does not escape from the pipe.
Can copper water lines touch?
Copper Water Pipes Touching Problem. Copper water pipes touching can be a big problem and can easily be fixed by separating them with a small piece of rubber or electrical tape. When the pipes touched each other, small amounts of electricity travel from one pipe to the other, over time producing corrosion.
What side is hot water under sink?
Plumbing for a kitchen sink includes a drain line, a pair of water lines, and a couple of valves. The hot water is on the left side while the cold water is on the right.
Can you run PEX through studs?
In some cases, the lines will have to be run across the wall studs. When running the pipes through the studs, first be sure to drill the holes in the center so that when it’s time to hang the wall board, the screws or nails don’t reach the pipes and damage the pipes.
Don’t forget to share the post !
