– Press the PHONE hard button.
– Select the ‘Settings’ tab on the touchscreen.
– Select ‘Advanced’.
– Scroll using the seek buttons on the touchscreen and select ‘Master Reset’.
– SYNC will ask you to confirm. Press ‘YES’ to continue.
– SYNC will confirm when the master reset is complete.
Push and release the Sel/reset button button 3 times repeatedly. The instrument cluster begins its self-test. Each successive press of the Sel/reset button initiates a new cycling of all the gauges. To end, turn the ignition switch to OFF, or vehicle speed exceeds 1.5 mph.
Thereof, How do I reset my GM instrument cluster?
Push and release the Sel/reset button button 3 times repeatedly. The instrument cluster begins its self-test. Each successive press of the Sel/reset button initiates a new cycling of all the gauges. To end, turn the ignition switch to OFF, or vehicle speed exceeds 1.5 mph.
Also to know is, Does a used instrument cluster need to be programmed? If your car is an X308 they instrument pack does not need to be programmed, I have swapped over clusters & never had to do the keys. The S Type & X Type as well as X350 all need to be programmed.
Subsequently, question is, How do I reset my digital speedometer?
Also, Where is the fuse for the gauges?
Find one fuse box in the engine compartment close to the driver’s side. The other has most fuses that you may need and is on the driver’s side under the instrument panel.
Does changing instrument cluster change mileage?
depending on the age of the cluster you may not have to do anything, newer electronic odometers are just a display, the actual mileage is stored in the ECU, changing the IC should not affect the mileage displayed.
What would cause all my gauges to stop working?
Once one of the gauges in your car stops working, there can be one of two reasons for this. It could be either a bad sensor or a problem with the gauge itself. But it could also happen that all the gauges stop functioning at the same. This could be caused by defective instrument clusters or a blown fuse.
Why does my digital speedometer not work?
Common problems include, a faulty sensor, bad wiring, or dial malfunctions. Troubleshooting speedometer problems mostly call for a replacement of the speed sensor or cable, depending upon the vehicle. Both these repair jobs are simple to perform and can be done at home.
How much does it cost to fix instrument cluster?
The average cost for an instrument cluster replacement is between $886 and $907. Labor costs are estimated between $74 and $95 while parts are priced at $812.
How do I restore my instrument cluster?
Insert the ignition key into the ignition lock. Leave it in the 0 or I position. Push and hold the Sel/Reset knob (on the instrument panel by the fuel gauge), or the Sel/reset button on the right hand of the steering wheel below the Multi-Information Display Info button.
Why did all my gauges stop working?
Once one of the gauges in your car stops working, there can be one of two reasons for this. It could be either a bad sensor or a problem with the gauge itself. But it could also happen that all the gauges stop functioning at the same. This could be caused by defective instrument clusters or a blown fuse.
Is there a fuse for the speedometer?
If the mechanic believes that a fuse or bad wire has caused the speedometer to stop working, he or she will begin by examining the fuse to check if it has been blown. If so, the mechanic will replace the fuse.
What is the Illum fuse for?
The ILLUM 10 Amp fuse that is located on the internal fuse block is blowing. It does not always blow right away. It is a 10 amp fuse labled in the WH manual as ILLUM protecting the Instrument Panel Cluster, Audio Alarm, Body Builder Feed.
What does it mean when your dashboard stops working?
If the dashboard isn’t lighting up at all, your car might have blown a fuse. Removing the old fuse and replacing it should get the lights working again. While the new fuse may do the trick, it could also indicate a deeper electrical problem.
How do I know if my instrument cluster is bad?
– Dim or flickering gauges. One of the first symptoms of an issue with the voltage regulator is dim or flickering gauges. …
– Inaccurate or erratic readings. …
– Inoperable instrument cluster.
Where is the fuse for the instrument cluster?
Find one fuse box in the engine compartment close to the driver’s side. The other has most fuses that you may need and is on the driver’s side under the instrument panel.
How much does it cost to fix a cluster?
Instrument Cluster Replacement Cost – RepairPal Estimate. The average cost for instrument cluster replacement is between $916 and $936. Labor costs are estimated between $74 and $94 while parts are priced at $842.
Don’t forget to share this post 
References and Further Readings :
