You will need to start the diagnostics mode again, but this time turn the Centennial washer’s cycle knob right until only the “spin” light is lit and press “start”. The washer will do a quick cycle that will test all the washer functions.
Thereof, How do you put a Maytag washer in diagnostic mode?
Also to know is, How do you run a diagnostics and read error code on a Maytag washer?
Subsequently, question is, How do I reset my Maytag washer? – Unplug the washer for 1 minute from the electrical outlet.
– Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
– The motor has now been reset and is ready for you to start a cycle.
Also, How do you troubleshoot a Maytag washing machine?
– Washer won’t spin.
– Washer is making loud noise.
– Washer won’t agitate.
– Washer won’t drain.
– Washer vibrating or shaking.
– Washer fills slowly or will not fill at all.
– Washer leaking water.
– Washer won’t start.
How do you troubleshoot a Maytag washer?
– Washer won’t spin.
– Washer is making loud noise.
– Washer won’t agitate.
– Washer won’t drain.
– Washer vibrating or shaking.
– Washer fills slowly or will not fill at all.
– Washer leaking water.
– Washer won’t start.
Why does my Maytag washer not start?
If the washer overheats, the thermal fuse will blow. If the line fuse blows, the washer won’t start. To determine if the thermal fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it.
What does sensing mean on a Maytag washer?
When the Start/Stop button is pressed, and the Water Level knob is set to Auto Sensing, the washer will fill and begin sensing to determine load size and balance. … If the lid is left open for more than 10 minutes, the washer will cancel the cycle and pump out the water.
How do you clear the error code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do you read the error code on a Maytag Bravos washer?
How do you reset a washing machine?
Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds.
Why is my Maytag washer not starting?
First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. … To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
How do I know if my washing machine actuator is bad?
When the actuator fails there is usually and awful lot of grinding noise, and the tub and agitator operate at a slow speed, if at all. In most models, you will have an F7 -E1 or E5 error code in the display.
How do you run a diagnostic test on a Maytag Centennial washer?
Now you can do run a Maytag Centennial automatic diagnostic washer cycle. You will need to start the diagnostics mode again, but this time turn the Centennial washer’s cycle knob right until only the “spin” light is lit and press “start”. The washer will do a quick cycle that will test all the washer functions.
How do you diagnose a washing machine problem?
– Check that the washer is plugged in securely.
– Check the circuit breaker or fuse box.
– Test the outlet for current.
– Check that the water supply valves are turned on.
– Inspect the filter screens.
– Test for overheating.
– Test the water level switch.
– Test the timer control.
Why is my Maytag washer not turning on?
Check to see if a household circuit breaker or Ground Fault Circuit Interrupter (GFCI) outlet has tripped. If so, reset the circuit breaker or Ground Fault Circuit Interrupter. If the washer is on a fuse box, check to see if a fuse has blown and replace it, if necessary.
How do you run diagnostics on a Maytag Bravos washer?
– The washing machine should be in standby (off) mode.
– Press and release the following buttons within 4 seconds. …
– if successful “dt” should display on the washing machines indicator.
– Whithin 5 seconds press “Start” all indicator lights should come on and 88 should be displayed.
Don’t forget to share this post 💖
References and Further Readings :