Q. To support a beam for a residential deck, does a Sonotube pier need any rebar? A. … We usually recommend that a minimum of two pieces of #4 rebar be placed vertically in an 8-inch-diameter concrete pier supporting a structure.
The rule-of-thumb is to use a tube diameter 3 times the post width, therefore use a 12” diameter Sonotube for a 4×4” post.
Thereof, What size sonotube do I need for a 6×6 post?
The pergola will dimension 11’x 11.5′ on center of post with 6×6 posts (4 posts), tied together with sandwiched 2×12 beams. I’ve laid out footer locations and am about to dig for 8″ sonotube forms.
Also to know is, Do you have to put rebar in footings? Using Rebar for Concrete Deck Footings Plain concrete deck foundations without rebar are acceptable under the minimum standards of construction established in the International Residential Code. … Footings with large bearing areas or unstable soil can benefit from adding rebar to prevent cracking.
Subsequently, question is, How do you anchor a 6×6 post to concrete? – Hold your drill plumb. Use a drill with a hammer drill bit to install a concrete sleeve anchor into the center of the concrete footing.
– Don’t over tighten the bolt. Install the Adjustable Post Base to the sleeve anchor and tighten the bolt to secure the attachment.
– Place your foot behind the post when nailing.
Also, What size concrete piers do I need?
Pier diameter. My rule of thumb for pier diameter is “1 inch per foot of span.” Thus, a deck that spans 8 feet will stand comfortably on 8-inch-diameter piers, while a deck that spans 10 feet requires 10-inch-diameter piers.
How do you cut concrete piers?
Cut a chunk of plywood 3/4″ thick , down to a manageable size , cut a 1/2″ larger then the concrete pier is hole out, drop the ply over the pier , level it up using cribbing , then have your local concrete cutter bring his flush trimming concrete saw over.
How deep should Sonotubes be?
I dig my holes 2 feet in diameter so that I have some flexibility if I need to slightly adjust the placement of the tube. Also, the wider the hole, the easier it is to remove dirt as I dig deeper. When I reach our local frost depth of 48 inches, I add about 6 inches of stone to the bottom of the hole.
How do you attach 6×6 to concrete?
How do I know what size sonotube to get?
The rule-of-thumb is to use a tube diameter 3 times the post width, therefore use a 12” diameter Sonotube for a 4×4” post.
How do you secure a 6×6 post to concrete?
How do you calculate pier size?
To determine the load of a deck pier, you must take half the length of the joist span multiplied by half the length of the beam span (measured from pier to pier). This number is then multiplied by 50, which is the 40 psf live load, 10 psf dead load mentioned earlier.
How do you remove forms from concrete tubing?
If forms are to be removed, do so within 24 hours. Cut the QUIK- TUBE™ with a sharp knife or power saw set to the correct cutting depth. Simply peel the form away from the concrete.
How do you set a post holder in concrete?
Can you pour concrete without rebar?
Not all surfaces need concrete rebar reinforcement, but adding it makes concrete stronger and more resistant to large cracks. … Without rebar reinforcement, concrete is highly prone to cracks due to tension forces. Rebar helps prevent cracks from growing wider largely by preventing cracked slabs from moving apart.
Should deck posts be set in concrete?
There are several ways to set deck posts; we recommend attaching the posts to concrete footers above the ground. This helps to prevent wooden posts from rotting. Set footers a minimum of 6” below the frost line for your area to prevent movement during freezing temperatures.
How do you anchor metal post to concrete?
Do you need rebar for 4 inch slab?
No, you do not need rebar for a 4-inch slab of concrete on grade. A 4-inch-thick slab cast on the ground and in permanent contact with it will float and rebar is not required. Rebar is recommended on concrete measuring 5 – 6 inches thick.
Don’t forget to share this post 💖
References and Further Readings :
