Chair rail moulding adds a decorative touch of elegance to any room. In modern times, chair rail is a chic design feature, but historically it was applied in dining rooms to protect plaster walls from being dinged by chairs – hence the name.
Thereof, What is plate rail?
: a rail or narrow shelf along the upper part of a wall for holding plates or ornaments.
Also to know is, How do you put a plate groove on a shelf? – Measure 2 inches out from the back edge of the shelf at both ends of the shelf and make a pencil mark at each location.
– Place a straightedge or yardstick on the shelf, connecting the two marks. …
– Set a router to make a U-shaped groove, 1/4-inch deep. …
– Sand any rough edges along the groove with fine sandpaper.
Subsequently, question is, How high should a plate rail be? The most common measurement seems to be 3″ in between frames and 4″ between the top of the baseboard and the bottom of the frame. Also, 4″ between the top of the frame and the bottom of the chair rail were most common.
Also, How do you secure a display plate on a shelf?
Stand plates on the shelf behind the stick. Allow the front edge of the plate to slide up against the stick and lean back against the wall to secure it.
What is the purpose of chair rail?
Chair rail creates a decorative element in a room, but it also acts as a protective barrier from wear and tear in high traffic areas or spaces where furniture is moved around often. This trim is commonly used in dining rooms, breakfast nooks, living rooms and foyers.
What is a plate groove?
The groove in a plate shelf is approximately 1/4 to 1/2 inch wide and situated in a spot that is far enough from the back edge of the shelf to keep the plates upright without letting them topple forward. This spot can vary depending on how large or small the plates are.
What is the difference between wainscoting and chair rail?
Wainscoting is a TYPE of panel molding and it signifies a decorative wooden treatment that is usually at chair rail height (approximately 32″ above the floor) or below. … Panel molding reaches above the chair rail (typical chair rail height is approximately 32″ above the floor) and sometimes covers the entire wall.
How do you display China on shelves?
Stand plates up on grooved shelves, such as those in china hutches, or by using plate stands. Metal plate stands are sturdier than their plastic counterparts are, but plastic plate stands are sufficient for displaying smaller pieces such as dinner and salad plates.
How do you install rail molding?
How do you measure for a chair rail?
To determine the height of the chair rail, measure the height of the ceiling and divide it by three. The general rule is that the chair rail should be about 1/3 of the way up from the floor (between 32″ and 36″ for an 8′ ceiling). You can also slide a chair up to the wall and mark where it would hit the wall.
How do Chinese cabinets hold plates?
Some china cabinets have a plate rail instead of a groove. The rail is basically a very thin piece of wood that’s raised slightly from the shelf. Set the bottom of the plates behind the rail, then rest the backsides of the plates against the back of the cabinet.
How do you make a plate shelf?
– Wood dowels ( cut to 6″ lengths, each approximately 3/8″ in diameter )
– 2 strips of apx. 1″ x 1″ wood ( cut to the length you’d like your plate rack to be )
– 2 stips of 1″ x 1″ wood (cut to 3″ lengths)
– Wood glue.
– 1/4″ dowel pins (1/4″ refers to the diameter)
– Saw.
– Drill.
– Drill bits.
How high should wainscoting be with 9 foot ceilings?
The traditional rule of thumb is that wainscoting height should be a third of the wall’s height, including the cap or any moldings. So if you have 9-foot walls, then 3-foot (or 36-inch) wainscoting will look great.
Are china cabinets out of style 2020?
China & Curio Cabinets Having a nice set of china and crystal might have been a status symbol which needed to be shown off and admired back in the day. (Not so much anymore!) With the decline in formal dining and dining rooms, china cabinets have gone the way of the Dodo. Curio cabinets are a close second.
Can you install crown molding without nail gun?
Installing it is as simple as buying a box of itty-bitty finishing nails and hammering in the molding. Seriously, you do not even need a nail gun. Here’s the whole step-by-step for how to install baseboards and crown molding—note that most of the work happens in the planning phase. The actual install takes no time!Jun 29, 2018
What is the best height for wainscoting?
What is the proper height for wainscoting? Generally, the cap sits about one-third the way up the wall. So if the ceiling is 9 feet, go for 3-foot wainscoting. For taller wainscoting, such as one with a plate rail, cap it two-thirds the way up the wall.
Don’t forget to share this post 💖
References and Further Readings :