– Bostitch N66C-1 Coil Siding Nailer. BOSTITCH Coil Siding Nailer, 1-1-1/4-Inch to 2-1/2-Inch… …
– Hitachi NV65AH2 Coil Siding Nailer. …
– Bostitch N66BC-1 Nailer. …
– Freeman PCN65 Coil Siding Fencing Nailer. …
– Makita AN611 Siding Nailer. …
– Hitachi NV75AN 1-3/4 Inch to 3-Inch Coil Siding / Framing Nailer.
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. … Don’t drive nails into the siding at an angle.
Thereof, What kind of nail gun do you use for Hardie board?
Name More Details
———————————————— —————
MAX CN565S3 “SuperSider” Siding Coil Nailer Check On Amazon
Hitachi NT65M2S 16-Gauge Finish Nailer Check On Amazon
P4FRFNCB Pneumatic Framing & Finishing Combo Kit Check On Amazon
Also to know is, Do you nail or screw Hardie board? James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in. from the top edge and no closer than 3/8 in.
Subsequently, question is, Can you use a brad nailer for siding? Nail Gun for Siding A pneumatic nail gun should be used for siding installation, especially for harder fiber cement siding. … You cannot use a brad gun for installing siding because the brads leave two holes for each brad and do not hold up as well as siding nails.
Also, What kind of nails do you use on Hardie board?
Fasteners must be corrosion resistant, galvanized, or stainless steel. Electro-galvanized are acceptable but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.
Can you screw into Hardie board siding?
Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. … Screw the HardieBacker into the floor, using 1¼-inch backerboard screws and using one screw every 8 inches.
How do you drill through Hardie board siding?
Equip a power drill with a masonry drill bit for small holes or a carbide hole saw for larger holes, preferably a saw designed for use with fiber cement siding. Mark the position where the hole should be drilled. Put on safety goggles whenever drilling, sawing or nailing cement fiber siding.
Can you drill into cement board siding?
It can be cut and drilled just like wood. However, drilling through cement-fiber siding goes better if you use a carbide drill bit, as opposed to a regular steel drill bit. Cement-fiber siding can be drilled while installed on a house or prior to installation.
How do you fasten Hardie board?
Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.
What do you fasten Hardie board with?
Hardie board comes with a 30-year manufacturer’s warranty, but that means you need the nails to last at least that long too. James Hardie recommends that nails be hot dip galvanized (at a minimum) or stainless steel (as a best practice).
Can you screw Hardie board siding?
HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. … Fasteners shall be installed between 1 in. and 3/4 in.
Can you put nails in Hardie board?
James Hardie recommends that nails be hot dip galvanized (at a minimum) or stainless steel (as a best practice). Anything less and the nails may start to rust, leading to stains on your beautiful siding.
What nails do you use with Hardie siding?
Fasteners must be corrosion resistant, galvanized, or stainless steel. Electro-galvanized are acceptable but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.
Is Hardie board siding expensive?
Hardie board siding costs anywhere from $0.80 to $6.00 per square foot material installed on a home. If you were to replace an average size home with 1,500 square ft of materials you could expect to pay anywhere from $1,200 to $9,000 in replacement costs.
What kind of screws do you use for Hardie board?
In compliance with the tile industry, James Hardie recommends 1-1/4” long galvanized or stainless steel roofing nails (0.121” shank x 3/8” HD) or 1-1/4” long corrosion resistant ribbed waferhead screws (No. 8-18 x 3/8” HD).
What do you use a brad nailer for?
Brad nail uses include decorative trim, picture frames, paneling, birdhouses, narrow trim around windows or doors, shoe moulding, quarter-round moulding and other thin cuts of wood.
How do you attach Hardie siding?
Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.
Don’t forget to share this post 
References and Further Readings :
