If the red and black wires are connected together already and energized, yes you can do that but you will need a pull chain light or a remote control, if they are not switch controlled.
Table of Contents
READ ALSO
Likewise, Is red or black positive?
Each battery has two metal terminals. One is marked positive (+), the other negative (-). There are also positive and negative cables in the jumper cable set. The red one is positive (+), the black one is negative (-).
Also, Where do the red and black wires go on a light switch?
The black (hot) wire goes to the brass screw or into the hole in the back of the device on the same side as the brass screw. This wire is sometimes red. The green or bare copper (ground) wire, if the device has one, attaches to the green screw terminal on the switch or to the electrical box.
Moreover, What happens if you switch black and red wires?
If you switched the wires, what would happen? Red is positive charge, black is negative charge. If you aren’t running if you aren’t connected correctly.
Why is there a red wire in my light switch?
What are Red Wires? Red wires are usually used as secondary hot wires. Red wires are also hot and should be clearly marked to avoid the dangers of electrocution. Red wires are commonly used when installing ceiling fans, where the light switch maybe.
Do I connect red or black first?
When removing the old battery, remember to first disconnect the cables from the negative terminal, which is usually black and has a minus (-) sign then disconnect the cables from the positive terminal, which is usually red and has a plus (+) sign.
Which wire is positive when both are black?
If the multi-colored wire is black and red, the black wire is the negative wire, while the red one is positive. If both wires are black but one has a white stripe, the striped wire is negative, while the plain black wire is positive. Look in the owner manual to determine which wires are negative in a car.
Is blue wire positive or negative?
Yellow is positive, blue is negative.
Why are there 2 black wires on light switch?
The bare or green-wrapped ground wires serve as a backup to divert the power safely away in case of an electrical fault. In most cases, two black wires will be attached to the switch’s two terminal screws. … The ground wires will be connected to each other and attached to the grounding screw on the switch.
Can you wire a light switch wrong?
If either wire at the light fixture is still hot then the switch is wired incorrectly. If one of the wires is still hot at the light fixture with the switch in the off position, then you most likely have the light switch on the neutral wire.
What are the white black and red wires?
The white wire is always neutral, and when the cable has only two conductors, as most 120-volt cables do, the hot wire is black. … The red wire is for the light switch. This configuration, sometimes called a half-hot or split-tab outlet, is becoming increasingly popular, so it’s good to know how to wire it.
Is the common wire the hot wire in a 3 way switch?
Black wire: This is a hot wire that carries electricity from the power source to the first switch in a typical 3-way setup. It’s also called the “common wire” or the “line wire.” Unless the breaker is off, this black wire is always hot.
Where does the red wire go on a light switch?
The red wire will go on one of the brass screws, but whether it goes on the left or the right depends on how the room is wired. If you don’t know how it was, connect the red wire to one of them, turn the power back on, and try the lights. If the switches malfunction, switch the lower wires on the new switch.
Do you need the red wire on a light switch?
Red wire: The second hot/traveler wire is the red wire that serves the same purpose as the black wire between the two switch boxes. Depending on toggle switch configuration, either the red wire or the black wire will be hot if the light is on, but not both.
Are red and black wires the same?
The standard way to power a split-tab outlet is to run a three-conductor cable to a wall switch. The cable has a black wire, which connects directly to the circuit, and a red wire, which connects to the switch.
What color is ground wire on car battery?
The ground wire in a car with a negative earth will be black while the ground wire in a car with a positive Earth will be red. The battery in a positive earth car may have been converted.
What happens if you connect the negative terminal first?
Negative pole first: Whole car (except a few parts like the positive pole) are connected. Any mistake with the other lead will lead to a short. … If you mess up by touching the car with the other lead nothing will happen.
Why do you connect the positive terminal first?
Connect positive first, negative having less potential won’t arc. The higher the voltage, the greater the chance of arcing and fusion. On a car if negative first and you are touching any metal part of car, when attaching positive there is possibility of arcing through you. Your body becomes part of the circuit.
Which wire is live when both are same color?
Identify the neutral wire in the fixture by looking at the wires. In most modern fixtures the neutral wire will be white and the hot wire is red or black. In some types of fixtures, both wires will be the same color. In this case, the neutral wire is always identified by some means.
Why do I have 2 black wires and 2 white wires?
the black and white wires from the power supply side need to be attached to the line side of the new outlet. (it should say this on the back of the new outlet) and the other 2 are to be attached to the Load side of the outlet.
What does blue wire mean?
Blue wire generally refers to a type of wire or cable that is added to a hardware product at a factory in order to resolve design problems. Blue wires are also known as bodge wires in British English.
Which wire does the blue wire go to?
Blue wire is for the light, if light is included with the fan. White wire is neutral. Green wire is for the ground. Red wire is sometimes included and acts as a conductor to carry power to the light kit.
Do I connect the blue wire to the black wire?
single Switch Ceiling Fan Wiring
Note that the blue wire is connected to the black fan wire so that they can both be operated by the same switch. Connect the ceiling fan blue wire to both the black fan wire and the black wire from the ceiling. … These wires are commonly green, yellow or bare copper.
