If your washer is still not working correctly, you can try the Cabrio reset procedure. Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL.
Likewise, How do you troubleshoot a Whirlpool Cabrio washer?
Clean all contact areas on the lid and the washer. Try unplugging the washer to allow the control panel to reset. Plug the washer back in and see if the problem resolves. If the door sounds like it is engaging, but doesn’t, it is time to run a diagnostic test.
Also, Why won’t my Cabrio washer fill with water?
Washing Machine Won’t Fill Because Water Inlet Valve Defective. Washing machines have a water inlet valve that allows both hot and cold water into the unit. … No continuity indicates an issue with the valve. When the water inlet valve is the cause for a Whirlpool Cabrio washer not filling with water, it must be replaced.
Moreover, How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Why is my Cabrio washer not working?
The first step you should take is unplug the washing machine for at least 5 minutes. Plug it back in and see if the board was reset. If the error code is still present you’ll need to unplug the machine again and remove the back panel. … In conclusion, those are the most common issues with Whirlpool Cabrio washers.
Why won’t my Whirlpool Cabrio fill with water?
If you find your Whirlpool Cabrio washer not filling with water, the inlet hoses and screens may be at fault. The hoses connect the main water supply to your machine. … To inspect the screens for signs of clogging, turn off the main water supply. Then, detach the inlet hoses from both the washer and the faucet.
Why is my Cabrio washer not draining?
Check the washer’s discharge hose if the water fails to drain from the washtub. Look for any kinks in the Cabrio washer’s discharge hose that could stop the water from draining. Straightening the hose ensures proper draining. Check the installation of the discharge hose if the washer still fails to drain.
Why is my Cabrio washer not spinning?
If your washer doesn’t spin or pump water out but the motor is running, your washer probably has a frozen pump pulley. If so, you need to replace the pump. To check the pulley, remove the pump from the washer and try to rotate the pulley manually. If it doesn’t turn freely–if it’s frozen or stiff–replace it.
Why is my Whirlpool washer not holding water?
The most common thing that causes this is that someone taped the drain hose to the drainpipe so that the water will not back out the drain during pump out. The best way to fix this is to clean out the drainpipe so that the water drains freely enough that it doesn’t back out and remove the tape from the drain hose.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
Why my washer stopped working?
Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.
How do you reset a Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
How do you force a Cabrio washer to drain?
How to Drain a Whirlpool Cabrio Washer
- Press “Pause/Cancel” twice on the control panel.
- Press “Power,” and turn the cycle knob to “Drain & Spin.”
- Push “Start.” The washing machine automatically unlocks when the water has drained.
How do I manually drain my Whirlpool washer?
If not, follow these steps:
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose at the back of the washing machine.
- Step 3: Drain the water.
- Step 1: Turn off the power and lay down towels.
- Step 2: Locate the drain hose.
- Step 3: Drain the water.
- Step 4: Scrub the filter.
Why is my washer not draining completely?
There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do you fix a Whirlpool Cabrio washer that won’t spin?
If your Whirlpool Cabrio washer will fill with water but won’t spin, the lid lock switch is probably bad. To diagnose this problem you’ll want to put the washer in a spin mode. Next, open the lid and insert a screwdriver into the lid switch actuator hole.
Why will my washer not spin?
If the belt mechanism is loose or slipped or the belt is damaged, it may not be spinning with enough force. If the belt is broken or fully off the rollers, then it won’t spin at all. A washer that won’t spin isn’t washing. If it can’t agitate clothes, then clothes don’t get clean.
How do you fix a Whirlpool washer that won’t fill with water?
Whirlpool Washer fills slowly or will not fill at all
First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
Why does my washer not hold water?
If the washer is draining the water while it is filling, check the following: Make sure that the house drain is at least 30 inches high. If so, check to make sure the drain hose is not pushed too far down into the drain. … It attaches to the hose and the back of the washer to lift the drain hose up.
Why does my washer start then stop?
The door lock secures the washer door shut during operation. Once the washer door is closed, the washer can begin operating. If the washer door is not latched shut, the door switch prevents the washer from operating. If the door lock is defective, the washer may stop mid cycle.
Why does my Whirlpool washer not start?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Why does my Whirlpool washer keep shutting off?
Whirlpool Washer Keeps Shutting Off
One thing that may cause your washer to shut off is inconsistent water flow. If your washer is not getting enough water, it will shut down the cycle. This could be because of interrupted flow to the machine caused by a drain blockage or plumbing issue.
