How to Reset a Kenmore Elite HE Washer Press the “Stop” button twice, and then press the “Power” button. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”). Press the “Start” button to complete the reset process and restart the washing machine.
similarly, What would cause a Kenmore washer not to spin?
If the drive belt is broken or loose, replace it. The motor coupling connects the motor to the washing machine transmission. If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission. … If the door latch is defective, the washer will not spin or start.
on the other hand, How do I troubleshoot my Kenmore washer?
Kenmore Washer Troubleshooting
- Bad lid switch. If your washing machine does not stop every time you open the lid, your lid switch is bad. …
- Clogged waste hose. If your washing machine does not drain the waste water, the waste hose might be clogged. …
- Bad drain pump. …
- Bad pump motor. …
- Broken drive belt. …
- Bad tub motor.
also, How do you run a diagnostic on a Kenmore washer? Close the door with the washer empty. Select “Drain/Spin” or “No Spin” by pressing the SPIN SPEED button. Within 5 seconds, push the “Prewash” option four times. The diagnostic should begin when C:00 light up.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do you fix a Kenmore washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
What causes a washer not to agitate or spin?
The washer transmission might be worn out or defective. Transmissions have gears in them that can fail causing the washer to not spin or agitate. … If the motor is turning the transmission, but the washer won’t spin or agitate, consider replacing the transmission.
Why does my washer not spin all the water out?
If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Check these areas and remove anything that may be clogging the draining system on your washer.
How do you troubleshoot a Kenmore 500 washer?
Troubleshooting Guide for a Kenmore Washer 500 Series
- Check to make sure that the washing machine is properly plugged into a grounded, three-prong electrical outlet.
- Check your fuse box or circuit breaker to make sure that the fuse is not blown or that the circuit breaker is not tripped.
Do Kenmore washing machines have fuses?
The switch can be found on the inside close to the door frame. Some models also have a special “lid-switch” fuse close by the lid switch within the control panel. A blown fuse will not allow the washer to fill with water.
How do you run a diagnostic on a Kenmore front load washer?
Here is what I did to run a diagnostic.
- With the washer empty, close the door.
- Push “control/on” or “Start”
- Select “Drain/Spin”
- Select “No Spin” by pressing SPIN SPEED touchpad.
- Push “PREWASH” option four times within 5 seconds. …
- C:00 should light up and begin the diagnostic.
What does UE mean on my Kenmore washer?
The uE and UE error codes on your Kenmore top-load washer both mean the washer won’t run the spin cycle because the load is unbalanced. … The UE error code appears if the rebalance routine fails to evenly distyribute the load after 3 attemps and the control board stops the washer.
How do I reset my Kenmore front load washer?
To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.
How do you reset a Kenmore 100 Series washer?
Motor Reset Procedure:
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
- The motor has now been reset and is ready for you to start a cycle.
Why won’t my washing machine finish its cycle?
Drainage Problems
If the washing machine doesn’t drain properly then something blocking the pump could have caused the washer to stop mid cycle. … General overheating is again a possible cause for your washer to stop mid-cycle, many washing machines have built-in sensors.
Why is my washer stuck on the rinse cycle?
If your washer works fine up to the point of the rinse cycle, this is a likely sign that your cold water supply faucet has malfunctioned, since this is the point at which cold water is needed. … It is also possible that the water filters inside the pipes leading into the washer have become clogged.
How do you force a washer to drain?
How to Manually Drain a Top-Loading Washing Machine
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose at the back of the washing machine. …
- Step 3: Drain the water. …
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose. …
- Step 3: Drain the water. …
- Step 4: Scrub the filter.
Why isn’t my washer washing my clothes?
A common reason why your washing machines is not cleaning clothes properly is because the line leading from the detergent tray to the drum has become clogged up with washing up powder. This means that just a small amount of detergent actually reaches the drum – the rest of it becomes stuck behind the blockage.
Why are my clothes too wet after the spin cycle?
Loading Too Many Items
Overloading can lead to an imbalance that reduces the washer’s spin speed, leaving clothes too wet after spin cycle completes. If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle.
How do you fix a washing machine that will not spin?
- Redistribute an off-balanced load of laundry . …
- Level an off-kilter washer . …
- Check the power source. …
- Stop using an extension cord. …
- Inspect the spin switch. …
- Stick to high efficiency detergent with a front-load washer . …
- Undo any kink in the hose. …
- Track down a blockage in the drainage system.
What causes a washer to not spin out all the water?
If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. Check these areas and remove anything that may be clogging the draining system on your washer.
Why does my Kenmore washer take so long to wash?
A washer that continuously takes too long to wash may have a malfunctioning load sense system, or greater problems with its control panel. There may also be issues with your water inlet valve, which pulls water into the appliance for each cycle.
How do you clean the lint trap on a Kenmore washer?
How to Clean the Lint Trap in a Kenmore Washing Machine
- Lift up the lid to your Kenmore washing machine.
- Twist off the top of the agitator, the bar in the center of the machine that moves the laundry around.
- Pull out the plastic lint trap. …
- Screw the agitator’s top back on.
Don’t forget to share the post !