How do I clear F9 code?

How to Remove the F9 Code From Maytag

1. Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. …
2. Open the oven door and check the door latch. …
3. Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. …
4. Press the oven door shut gently. …
5. Test the oven.

Likewise, How do I reset my Whirlpool front load washer?

The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

Also, What does F9 error code mean?

An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. The automatic door lock mechanism prevents the oven door from being opened when the oven is set for “Clean” mode.

Moreover, How do I fix my oven F9?

The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.

What does E1 and F9 mean on a Maytag washer?

If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. … If not, the washer could siphon (fills and drains at the same time).

Do Whirlpool washers have a reset button?

How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

Why is my Whirlpool washer stuck on sensing?

A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.

How do I reset my F9 Whirlpool stove?

Reset power to the product:

Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the oven/range for one (1) minute to ensure the error code does not display again. Verify oven operation.

How do I fix F9 error on Maytag oven?

Maytag Stove F9

Then opened the door. After that, it wouldn’t shut, got F9 and lots of beeps. The fix is to open the door, but hold in the door light button. Push the latch that should lock the door to the unlocked position, the display will show “lock” (I think).

How do I fix error code F9 on Jenn AIR?

F9 – Door Lock Safety Circuit On Power Relay Board Sensed – Replace power relay board. FF – Invalid Temperature Reading On Power Relay Board – Check oven temperature sensor and wire harness. If ok, replace power relay board. F – Communication Error Between Boards – Check wire harness for continuity.

How do I fix the F9 on my Whirlpool oven?

Reset the appliance

1. Power unit down by turning off the circuit breaker(s) for one (1) minute.
2. Power unit up by turning on the circuit breaker(s).
3. Monitor the range or oven for one (1) minute to ensure the error code does not display again.
4. Verify the range or oven operation.

How do I reset my Whirlpool oven?

Reset power to the product:

1. Power unit down by turning off the circuit breaker(s) for one (1) minute.
2. Power unit up by turning on the circuit breaker(s).
3. Start a bake cycle.
4. Monitor the oven for one (1) minute to ensure the error code does not display again.
5. Verify oven operation.

How do I fix F9 error on Maytag oven?

F9 means that your door latch assembly has failed. Try turning the breaker off to the unit for 60 seconds to see if it will reset. If not, then try to set the self clean, wait 60 seconds and cancel it to see if that will reset the door latch assembly.

How do you fix E1 F9 error on a Maytag washer?

F9 E1 Code in the display: Is the drain hose properly installed?
…
Is the drain hose properly installed?

1. Make sure the drain hose is not kinked or clogged.
2. Use the U-shaped drain hose form on the drain hose.
3. The standpipe (drainpipe) height requirements are 96″ (244 cm) maximum and 39″ (99 cm) minimum.

How do I fix E1 error on my washing machine?

If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.

Why is my Whirlpool washer not working?

One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.

How do I fix the f20 code on a Whirlpool washer?

To reset the f20 error code, exclude the program crash of the Whirlpool washer. To do this, de-energize your washing machine for 10-20 minutes, then turn it on back. If the error disappears from the display, the problem is successfully eliminated.

Will unplugging a washing machine reset it?

On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.

How long should Whirlpool washer be in sensing mode?

These sensing spins may take 2 to 3 minutes before water is added to the load. The washer will then move the load briefly, pause to allow water to soak into the load, and resume adding water.

Why is my washer taking so long sensing?

A washer that continuously takes too long to wash may have a malfunctioning load sense system, or greater problems with its control panel. There may also be issues with your water inlet valve, which pulls water into the appliance for each cycle.

Why is my Whirlpool oven not working?

An electric oven not heating up can often be attributed to a defective bake element. This Whirlpool oven heating element is a metal coil located at the bottom of electric ovens. When you turn on the oven, wires inside the coil receive electrical current that heats the metal, providing the heat you need to cook food.

Why does my Whirlpool stove say PF?

Whirlpool PF – Power failure (not a failure mode)

The manufacturer has assigned this error or fault code to indicate that the appliance lost power temporarily. Press CANCEL to clear the display.

How do I reset my Maytag oven?

Simply turn off the oven, unplug it for five minutes, and then plug it back in and restart. Also, make sure the fuse wasn’t tripped at the circuit breaker and that the outlet provides the correct voltage for the oven.

What does F5 mean on a Maytag oven?

F5 – Watchdog and Hardware Conflict – Replace control board (clock). F7 – Function Key Stuck or Shorted – Replace touch pad, or touch pad and control board (clock) if one assembly.