Turn off the home’s hot and cold water supply taps/valve. Remove the water inlet hoses from the washer. Ensure to have a bucket to drain the remaining water from the hoses. Check the inlet filters on the inlet valves of the washer, inspect for any mineral deposits or other debris that may be clogging them.
Table of Contents
READ ALSO
Likewise, How do I troubleshoot my LG washer?
How to Troubleshoot LG Washer Problems
- Adjust your clothes. …
- Check the drum and drain filter for foreign objects. …
- Adjust the leveling feet at the base of your LG washer. …
- Check your hoses. …
- Check the power. …
- Contact LG customer support, if none of the previous steps help.
Also, Why is my LG washing machine showing IE?
An IE error code in LG washing machines signals that the machine’s washer was not filled with water in the allotted time. This could also be possible due to a faulty water inlet valve or a problem with a drain hose among others.
Moreover, How do I force drain my LG washer?
If you want to perform a drain-only cycle, turn on your LG washer and press the spin button and then press start. After a few minutes, the cycle will end and your washer should have drained out the water.
How do I fix E1 error on my washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
Are there any recalls on LG washers?
Incidents/Injuries: LG has received at least 343 reports of washing machines vibrating excessively, of which at least 187 involved minor property damage. … Consumers who have observed their recalled washing machine shaking excessively should immediately stop using it.
How do I run a diagnostic on my LG front load washer?
Press the POWER to turn on the washer. Place the mouthpiece of your phone between the Smart Diagnosis logo and the POWER button. After pressing the Start Diagnosis button, press and hold the TEMP button until a countdown displays on the washer. Keep the phone in place until the tone transmission has finished.
How do you fix IE error on LG top load washer?
An IE error code indicates that the washer was unable to fill with water .
…
- Turn off the home’s hot and cold water supply taps/valve.
- Remove the water inlet hoses from the washer. …
- Check the inlet filters on the inlet valves of the washer, inspect for any mineral deposits or other debris that may be clogging them.
Why is my LG washer not getting water?
Common solutions for: LG Washer fills slowly or will not fill at all. The water inlet valve opens to allow water to enter the washing machine. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
Why is my LG washing machine not draining?
Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.
How do I fix OE error on my LG top load washer?
Force drain the unit by starting a cycle and pausing it.
…
If you don’t have SPIN ONLY
- Power the unit ON.
- Select a cycle.
- Press START/PAUSE button to START the cycle.
- Allow a few minutes to pass so the cycle begins.
- Press the START/PAUSE button to PAUSE the cycle.
- Run an empty wash cycle to see if issue occurs again.
How do I manually drain my LG dishwasher?
How to force water drain in the LG dishwasher
- Start a dishwashing cycle.
- Let the dishwasher run for 45 seconds.
- Turn off the device.
- Then turn it on. The first 45 seconds of any cycle is drain only.
How do I clear E1 F9 code?
Filter clogged
It picks up trash and small objects before they reach the pump, instigating error code E1 F9. To access the filter, unscrew and remove the front panel. Then gently turn it and remove it from the groove.
What does E1 mean?
| Acronym | Definition |
|---|---|
| E1 | Everyone |
| E1 | Enterprise One (JD Edwards software) |
| E1 | Echelon 1 (US DoD) |
| E1 | European Basic Multiplex Rate (30 voice channels; 2.048 Mbps) |
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Are LG washers hard to repair?
LG front-loaders are less repair-prone than Frigidaire and GE but then the LG repair service left something to be desired. Of course, the most important thing to consider is performance. … So if you buy an LG washer and it breaks, consider calling your local repair shop first.
How long does a LG washer last?
The average life expectancy for washers and dryers is between 10 and 15 years. Front loaders are very efficient.
How much does it cost to repair LG washer?
The average LG washing machine repair cost will be from $225 to $300.
How do I run a diagnostic on my LG TV?
- Open the settings of the TV by pressing on the gear icon on the remote.
- Highlight or move the pointer over the All Settings option and open all settings.
- Select the Channels option.
- Move the pointer or highlight Channel Tunning.
- Press the 1 key on the remote five times quickly.
How long do LG washers last?
The average life expectancy for washers and dryers is between 10 and 15 years. Front loaders are very efficient.
How do I add water to my LG washer?
Adding the Water Plus Option to a cycle :
- While the cycle is running, press START/PAUSE to pause the cycle.
- Press WATER PLUS button to add Water Plus as a default option for that wash cycle.
- Press START/PAUSE to resume the cycle.
Is my LG washer using enough water?
Your LG washer is designed to use as little water as possible for efficiency. This is done by slowly filling the washer while checking the saturation level of the clothing. Once the clothing is completely wet, a sensor goes off indicating that the washer has enough water.
How do you fix a washing machine that won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do I know if my washing machine drain pump is bad?
You can check by looking for a few signs that a pump is dying or already dead.
- Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
- Open the washer lid in mid-cycle. …
- Wait for the washer to finish its cycle.
