First, unplug the cord and check the status of the outlet – voltage, polarity, grounding, dedicated circuit. If everything is normal, switch on the washing machine again, letting it stand for 1 – 5 minutes beforehand. This will help restart the unit and reset error code E01 F01.
similarly, How do I fix E1 error on my washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
on the other hand, How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
also, How do you reset the code on a Whirlpool washer? To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I clear E1 F9 code?
Filter clogged
It picks up trash and small objects before they reach the pump, instigating error code E1 F9. To access the filter, unscrew and remove the front panel. Then gently turn it and remove it from the groove.
What does IE mean on my washer?
An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen.
How do I reset my Kenmore top load washer?
How do I reset my Kenmore washing machine?
- Press the “Stop” button twice, and then press the “Power” button.
- Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
- Press the “Start” button to complete the reset process and restart the washing machine.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
How do I fix the code on my Whirlpool washer?
To remove the error display, press Power once. Then press Power again to restart the washer.
…
If pressing Power does not work:
- Unplug the washer or disconnect the power for one minute.
- Plug in the washer or reconnect the power.
- Re-select the cycle and press Start.
How do I fix the f25 code on my Whirlpool washer?
Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). Plug in washer or reconnect power. Check the MCU by looking for operations of the drive motor. Check the drive motor for powered rotations.
What does the Code F mean on a Whirlpool washer?
The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen. When the door fails to lock, the machine won’t run at all.
Why does my washer keep saying E1 F9?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. … If not, the washer could siphon (fills and drains at the same time). Lower drain hose if the end is higher than 96″ (2.4 m) above the floor.
What does the code E1 F9 mean on a Whirlpool washer?
F9 E1 Code in the display:
This error code indicates that drain times are longer than expected, typically over eight (8) minutes.
How do you fix E1 F9 error on a Maytag washer?
F9 E1 Code in the display: Is the drain hose properly installed?
…
Is the drain hose properly installed?
- Make sure the drain hose is not kinked or clogged.
- Use the U-shaped drain hose form on the drain hose.
- The standpipe (drainpipe) height requirements are 96″ (244 cm) maximum and 39″ (99 cm) minimum.
What does IE mean on my Kenmore washer?
The IE code indicates that the washer detects a problem with water fill. Make sure that the hot and cold water supply faucets behind the washer are fully open. … You can shut off the water supply faucets and check the inlet water screens on the back of the washer for debris or deposits.
How do you reset a Kenmore washing machine?
How to Reset a Kenmore Elite HE Washer
- Press the “Stop” button twice, and then press the “Power” button.
- Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
- Press the “Start” button to complete the reset process and restart the washing machine.
What does IE mean on IE mean?
i.e. is the abbreviation for the Latin phrase id est, meaning “that is.” This abbreviation is used when you want to specify something mentioned previously; it can be used interchangeably with “specifically” or “namely.” Here are some examples: “Only one city, i.e., London, has hosted the Summer Olympics three times.”
Does Kenmore washer have reset button?
Kenmore Elite Washers are the top-end model of washing machines the company makes available to consumers. … If you have started a load in your Kenmore Elite HE washer and need to reset it, simply press several buttons on the control panel.
Is there a reset button on Kenmore washer?
Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds. Press the Pause / Cancel / Stop button twice to clear the display.
How do you run a diagnostic on a Kenmore washer?
Close the door with the washer empty. Select “Drain/Spin” or “No Spin” by pressing the SPIN SPEED button. Within 5 seconds, push the “Prewash” option four times. The diagnostic should begin when C:00 light up.
Why won’t my washing machine finish its cycle?
Drainage Problems
If the washing machine doesn’t drain properly then something blocking the pump could have caused the washer to stop mid cycle. … General overheating is again a possible cause for your washer to stop mid-cycle, many washing machines have built-in sensors.
How do you reset a Unimac washing machine?
Once the bearings have been lubricated, reset the bearing counter by pressing and holding the STOP, BACK and LCD buttons. Press the arrow buttons until Reset Bearing Timer is highlighted and press ENTER.
Don’t forget to share the post !