If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
Likewise, Why is my LG washer flashing Le?
An LE error code on the washer’s display indicates that the motor is locked, possibly due to a heavy wash load. Large and heavy sized loads will put a strain on the motor, causing the LE code to occur. Performing a reset on the washer will normally resolve this error with a reduced load size.
Also, How do I clear E1 F9 code?
Filter clogged
It picks up trash and small objects before they reach the pump, instigating error code E1 F9. To access the filter, unscrew and remove the front panel. Then gently turn it and remove it from the groove.
Moreover, What does E1 mean?
| Acronym | Definition |
|---|---|
| E1 | Everyone |
| E1 | Enterprise One (JD Edwards software) |
| E1 | Echelon 1 (US DoD) |
| E1 | European Basic Multiplex Rate (30 voice channels; 2.048 Mbps) |
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do I get my LG washer to drain?
If you want to perform a drain-only cycle, turn on your LG washer and press the spin button and then press start. After a few minutes, the cycle will end and your washer should have drained out the water. Another way you can drain the water is by turning off your washing machine and unplugging it from the outlet.
Why does my washer keep saying E1 F9?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. … If not, the washer could siphon (fills and drains at the same time). Lower drain hose if the end is higher than 96″ (2.4 m) above the floor.
What does F9 mean on a washing machine?
F9 E1 Code in the display:
This error code indicates that drain times are longer than expected, typically over eight (8) minutes.
What does E01 and F09 mean on a washing machine?
Accepted Answer. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
Why is my AC showing E1?
If your air conditioner displays E1 in the display panel and won’t turn on, it means that the Room Thermistor (a device connected to the thermostat that detects room temperature) is shorted or defective, and you need to have your air conditioner serviced.
Why does my heater keep saying E1?
Answer: If your unit is currently flashing the manufacturer specific E1 Error code, that is indicating that there is not enough air flow to the unit, a bad internal fan, or a blocked air inlet.
What does E1 mean on electric fireplace?
Error E1 is displayed on the control panel. The overheat sensor has been turned on. The sensor will reset if the unit is unplugged. The unit needs to be plugged back in.
Do GE washing machines have a reset button?
Some machines have a button you push to reset its motor. … To reset washing machines that use the GE Hydrowave system, start by unplugging the washer for one minute. Plug the washing machine back in and then within 30 seconds, quickly open and close the lid six times. You’ll need to do this within a 12-second period.
How do you reprogram a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Why is my LG washer not draining?
Unbalanced Load. One of the most common reasons your LG washer won’t drain often results from an unbalanced load. Washing a large or heavy item can cause it to settle on one side of the washer drum. When this happens your LG washer won’t drain or spin properly and water will be left behind.
How do you force a washer to drain?
How to Manually Drain a Top-Loading Washing Machine
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose at the back of the washing machine. …
- Step 3: Drain the water. …
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose. …
- Step 3: Drain the water. …
- Step 4: Scrub the filter.
Why is my washing still wet after spinning?
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. … Often with this issue, whatever is causing it to not drain during the spin cycle means the water isn’t draining off fast enough and is essentially flowing back into the washer drum, re-soaking your clothing.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I know if my detergent is high efficiency?
Walk down the laundry detergent aisle in any store, and almost every single bottle, box, and the bag has a little symbol on the label: the letters “h” and “e” separated by a red dot on a field of blue surrounded by a white circle swirl. The HE stands for high-efficiency laundry detergent.
What is E3 error in washing machine?
The E3 error in Samsung washers means a drum overflow with water. The water level sensor sends a signal indicating that there is too much water in the drum. … Therefore, the washing machine stops washing. Then the device turns on the drain pump and displays the E3 error code.
What is E2 error in washing machine?
If the LED Lights are flashing with an E2, 5C or 5E error, it is an indication of water drainage issue. Water is not draining from the drum. To resolve the error issue, check the following: • Check drainage pump filter for blockages (e.g. lint, coins hair, clips)
What does FP mean on a washing machine?
Whirlpool washing machine error code FP
This error code means “drain failure”. If your washing machine is displaying this code it should still have some water stuck inside. … So if you have error FP you need to decide if the water has pumped away or not.
How do I fix error code F9?
Reset the appliance
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
What does F01 mean on a washing machine?
F01 — Electronic circuit board fault. Issue: Washing Machines is not operating – some or all functions are not selectable. Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again.
How do you clear the error code on a Whirlpool front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
