If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
similarly, What does IE mean on UE washer?
The IE error code on the LG washers display is indicating water did not fill the tub or it did not fill properly in the allotted time. This can be from a faulty water inlet valve, drain hose issue, bent water hoses, the water valves to the washer are not “open”, or there may be a communication or wiring harness issue.
on the other hand, How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
also, What does E1 mean?
| Acronym | Definition |
|---|---|
| E1 | Everyone |
| E1 | Enterprise One (JD Edwards software) |
| E1 | Echelon 1 (US DoD) |
| E1 | European Basic Multiplex Rate (30 voice channels; 2.048 Mbps) |
How do I fix E1 error on my Whirlpool washer?
E1 – water inlet alarm
- Check that the water faucets are not closed.
- Check that the water pressure in the house is over 20 kPa.
- Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
- Check that the drain hose is not below 27½” (700 mm) from the floor.
What does UE mean?
| Acronym | Definition |
|---|---|
| UE | Upper Extremity |
| UE | Unethical |
| UE | United Electrical, Radio and Machine Workers of America |
| UE | User Error |
What does IE mean on LG top load washer?
An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen.
How do I troubleshoot my LG washer?
How to troubleshoot:
- Open the stop valve to its full capacity. It may be closed or opened insufficiently.
- Check the intake hose. …
- The filter screen may be clogged with debris as well. …
- The intake valve is malfunctioning. …
- If the pressure switch is broken, you can repair your LG washing machine yourself.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
What are common problems with washing machines?
7 Common problems with washing machine
- Washing machine not starting. …
- Washing machine is noisy. …
- Excessive vibrations during operation. …
- Washing machine making noise when draining or not draining at all. …
- Washing machine over-filling or under-filling. …
- Washing machine not spinning. …
- Water leaking from soap drawer.
Why is my AC showing E1?
If your air conditioner displays E1 in the display panel and won’t turn on, it means that the Room Thermistor (a device connected to the thermostat that detects room temperature) is shorted or defective, and you need to have your air conditioner serviced.
What does E1 mean on electric fireplace?
Error E1 is displayed on the control panel. The overheat sensor has been turned on. The sensor will reset if the unit is unplugged. The unit needs to be plugged back in.
Why does my heater keep saying E1?
Answer: If your unit is currently flashing the manufacturer specific E1 Error code, that is indicating that there is not enough air flow to the unit, a bad internal fan, or a blocked air inlet.
Why does my washer keep saying E1 F9?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. … If not, the washer could siphon (fills and drains at the same time). Lower drain hose if the end is higher than 96″ (2.4 m) above the floor.
How do I fix a Whirlpool washer error?
If the Whirlpool washer displays the de error code on display, so there are problems with a door.
…
Manual Review
- Unplug the Whirlpool washing machine from the mains.
- Wait for 15-20 minutes while the control unit reboots.
- Reset the error by pressing the START button (On/Off).
- Check hatch locking.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
What does IE mean?
i.e. is the abbreviation for the Latin phrase id est, meaning “that is.” This abbreviation is used when you want to specify something mentioned previously; it can be used interchangeably with “specifically” or “namely.” Here are some examples: “Only one city, i.e., London, has hosted the Summer Olympics three times.”
What does UE stand for on phone?
In the Universal Mobile Telecommunications System (UMTS) and 3GPP Long Term Evolution (LTE), user equipment (UE) is any device used directly by an end-user to communicate. It can be a hand-held telephone, a laptop computer equipped with a mobile broadband adapter, or any other device.
What does IE mean on IE mean?
i.e. is the abbreviation for the Latin phrase id est, meaning “that is.” This abbreviation is used when you want to specify something mentioned previously; it can be used interchangeably with “specifically” or “namely.” Here are some examples: “Only one city, i.e., London, has hosted the Summer Olympics three times.”
How do I fix OE error on my LG top load washer?
Force drain the unit by starting a cycle and pausing it.
…
If you don’t have SPIN ONLY
- Power the unit ON.
- Select a cycle.
- Press START/PAUSE button to START the cycle.
- Allow a few minutes to pass so the cycle begins.
- Press the START/PAUSE button to PAUSE the cycle.
- Run an empty wash cycle to see if issue occurs again.
Are there any recalls on LG washers?
Incidents/Injuries: LG has received at least 343 reports of washing machines vibrating excessively, of which at least 187 involved minor property damage. … Consumers who have observed their recalled washing machine shaking excessively should immediately stop using it.
Why is my LG washer not filling with water?
If the water inlet valve is defective, the wash may fill slowly or not fill at all. … If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
How do I run a diagnostic on my LG front load washer?
Press the POWER to turn on the washer. Place the mouthpiece of your phone between the Smart Diagnosis logo and the POWER button. After pressing the Start Diagnosis button, press and hold the TEMP button until a countdown displays on the washer. Keep the phone in place until the tone transmission has finished.
Don’t forget to share the post !
