Fisher and Paykel Dishwasher Dishdrawer Error Code E6 = The first 4 program indicator lights are flashing. Error Code Cause: Flood switch activated. How To Fix: Turn the water and power off to the dishwasher and back on to try and reset. Check Flood Switch.
Likewise, What does F9 mean on a dishwasher?
A water pressure sensor is related to the F9 fault code on Glow-Worm boilers.
Also, What does E6 mean on dishwasher?
An E6 error code of the Bosch dishwasher means that there are problems with the sensor that controls the water turbidity. It is also called the Aqua Sensor. In the dishwasher, this sensor detects the turbidity of the water due to the presence of small particles of dirt, food residues and other things inside it.
Moreover, Where is the flood switch on a dishwasher?
The anti flood switch is in the bottom of the bas of the dishwasher. If its activated try and pull the dishwasher out and tip it 45 degs backwards and the water should drain out from the base and that way the flood switch will reset itself.
What does E2 mean on dishwasher?
E2 – Abnormally long drain time. Check to make sure that the drain line is not obstructed or bent in a way that restricts water flow. Make sure the drain line is routed below the height of the dishwasher and that it has not been extended. This will inhibit the ability of the drain function to operate properly.
How do I fix error e1 F9 on Maytag washer?
Possible Solutions
Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. Also make sure that the drain hose end is higher than 36 inches from the floor.
How do I clear the error code on my KitchenAid dishwasher?
Control Panel Reset
When powering down the unit and turning it back on doesn’t work, it may be best to reset the control panel’s computer. This is done by pressing two buttons, one after the other, at least five times each for a total of 10 presses. The door must be completely shut while the buttons are being pressed.
How do you run a diagnostic on a Fisher Paykel dishwasher?
Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.
How do you reset the flood switch on a dishwasher?
If you dont, you will need a new anti-flood switch. But try this first, turn off power to your dishwasher at the mains! Then you have to remove the dhswasher and tip it towards you about 45 degrees and hold it there for 30 seconds, then you can stand it up again.
How do I fix i30 error on my dishwasher?
Error i30: description
When the tank is full, fluid drains into the bottom of the pan. Then the float switch actuates, the dishwasher interrupts the cycle and displays error code i30. Try rebooting it by unplugging it for 30 minutes.
How do you Unflood a dishwasher?
To solve this problem, we recommend cleaning the food with a sponge and a few drops of dishwasher detergent. In addition, pour vinegar into the detergent tray and run a short cycle while the unit is empty. Ignoring routine maintenance can lead to severe leaks too.
How do I reset anti flood system on dishwasher?
But try this first, turn off power to your dishwasher at the mains! Then you have to remove the dhswasher and tip it towards you about 45 degrees and hold it there for 30 seconds, then you can stand it up again.
How do I fix E1 error on my dishwasher?
- Ensure Drain Hose is Installed Properly. Improperly installed drain hoses are a common defect with a lot of dishwasher installations. …
- Use the Proper Detergents. …
- Make Sure Your Door Isn’t Leaking. …
- Make Sure You’re Loading Dishes Properly.
How do I fix E3 error on my dishwasher?
Contact an Authorized Service Center. Error message E3 in integrated compact dishwasher indicates too much inlet water and/or a leak. We recommend requesting a visit by a service engineer. Warning: Turn off the dishwasher’s water supply to avoid flooding.
What does E1 mean on a dishwasher?
An E1 error code, programmed in the LG dishwasher, means that your appliance is leaking. This one is absolutely identical to an AE error code.
How do I clear E1 F9 code?
Filter clogged
It picks up trash and small objects before they reach the pump, instigating error code E1 F9. To access the filter, unscrew and remove the front panel. Then gently turn it and remove it from the groove.
How do I clear the error code on my Maytag dishwasher?
Error codes for Maytag HE dishwashers. Repair or Check | Remove power to the dishwasher for 5 minutes to try and reset. If the error code comes back when power is applied then check the wiring and the components. If the wiring and components check out then replace the electronic control board.
What does E01 and F09 mean on a washing machine?
Accepted Answer. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
How do I fix a blinking light in my dishwasher?
This problem often manifests as the Option and All Cycle lights blinking and usually signifies that the door opened in the middle of a cycle. The solution can be as simple as firmly closing the door until it latches. The lights should stop flashing, and the cycle should automatically resume shortly after.
Is there a reset button on a dishwasher?
Can you reset your dishwasher? Yes, you can reset your dishwasher by pressing the Start/Reset button on the appliance and waiting a few minutes. If your dishwasher still doesn’t start, you may need to reboot the entire system by turning off power to the appliance at the house circuit breaker or fuse box.
Why is the clean light blinking on my dishwasher?
The blinking clean light normally indicates that the control on the dishwasher detected a problem with the heating circuit. … The dishwasher will step through a short (10 minute) test cycle and then the control will be reset. You can cancel the cycle at any time after it is started by pressing the CANCEL button.
Why is my Fisher and Paykel dishwasher beeping?
The drainage hose may be blocked or kinked, or the connection to drainage pipe may be blocked. Ensure the drainage hose and connection to pipes are not blocked. Press ► once to stop the beeping, and then again to clear the fault. / ► to resume the wash program.
How do I fix E4 error on dishwasher?
Error message E4 in integrated compact dishwasher indicates failure of communication between main PCB with display PCB.
…
Resolution:
- Make sure that the drain hose is correctly connected.
- Make sure that the filters in the appliance are clean.
- Make sure that the kitchen sink drains correctly.
How do I fix the f2 on my Fisher and Paykel dishwasher?
Reset Procedures for the Fisher & Paykel Dishwasher
Press the power button to turn off power to the Fisher & Paykel dishwasher. Wait a few minutes and then press the power button to restore power. Turn off and unplug the dishwasher if the issue remains.