What is an F21 or F02 Error Code on my Maytag Front Load Washer? These error codes indicate that drain times are longer than expected .
…
Removing the Error
Table of Contents
READ ALSO
- Unplug the washer or disconnect the power for one minute.
- Plug in the washer or reconnect the power.
- Re-select the cycle and press Start.
Likewise, How do I get rid of F21 on my washing machine?
Here is what to do when your Whirlpool washer shows F21 error code: 1 – Check the drain hose located at the back of the washer to be sure it is not clogged, bent, or blocked in any way. Remove the drain hose and check to be sure there is no large lint blockage that is preventing the washer from expelling the water.
Also, How do I clear the error code on my Maytag front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Moreover, How do I reset my Maytag front load washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
How do you reset the error code on a Maytag washer?
How do you clear the codes on a Maytag Bravos washer?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. …
- The motor has now been reset and is ready for you to start a cycle.
How do you reset error F21?
Reset. When the “F21” error code appears, try pressing “Pause/Cancel” to stop the current wash cycle. If water remains in the washing machine tub, touch “Drain/Spin” to force a secondary drain cycle to remove the water. Once all the water drains, try selecting a new wash cycle and pushing “Start.”
How do you fix a Whirlpool washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do you clear the error code on a Whirlpool front load washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
What does E1 F9 mean on a Whirlpool washer?
F9 E1 Code in the display:
This error code indicates that drain times are longer than expected, typically over eight (8) minutes.
What does F mean on my Maytag washer?
Maytag F/02 – Drain Cycle Too Long
The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. … If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
Is there a recall on Maytag washers?
Important: CPSC Recall Remedy Notice Due to COVID-19
Description: The recall involves white Maytag front-load washers with model number MAH9700 and a serial number from 10188468GA through 11683946GJ. The model and serial numbers are located inside the door opening and below the rubber boot.
How do you reset a front-load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do you manually unlock a front-load washer?
Possible Solutions
- Turn off and unplug the washer/dryer.
- Close the water faucet.
- Wait until the drum has stopped rotating – never open the door while the drum is in motion.
- Wait until water and laundry have cooled down when washing with high temperatures.
How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Why is my washer stuck on sensing?
When Kenmore HE Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, most likely one of these 3 parts malfunction: Failed Water Inlet Valve or Inlet Valve Tap is in OFF position. Shift Actuator not able to change position, before Wash cycle. Control Board malfunctioned.
How do you reset a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do you run a diagnostic on a Whirlpool Duet washer?
Duet Washer Diagnostic Test Mode
Pick any three buttons on the Duet washer control except power, start, or cancel. Now do the key dance within eight seconds… Button 1, Button 2, Button 3, Button 1, Button 2, Button 3, Button 1, Button 2, Button 3 (You are pressing 9 buttons in 8 seconds so it needs to be pretty quick.)
Why is my Whirlpool front load washer not draining?
You need to make sure that the drain hose is not kinked at all. Straighten the hose to make sure that there is enough water flow and that you also remove any blockages from the drainpipe well. Ensure that you are using a U-shaped drain and secure it properly. Your instruction manual will show you how to do this.
What would cause my Whirlpool washer to not drain?
If your washer’s drain hose is kinked or bent, the washer will not be able to drain properly. The drain hose may also be obstructed by a small article of clothing. Check your drain hose and remove any obstructions, and straighten it if it’s bent. Make sure the hose is placed less than eight feet above the floor.
What is the problem with Whirlpool washing machines?
The machines, branded as Hotpoint or Indesit, were sold for more than five years, but their door locking system can overheat creating the risk of fire. Owners face the prospect of doing without hot washes for months until products are fixed or replaced.
Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I reset my Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
How do I fix E1 F9 error on Whirlpool washer?
Filter clogged
It picks up trash and small objects before they reach the pump, instigating error code E1 F9. To access the filter, unscrew and remove the front panel. Then gently turn it and remove it from the groove.
How do I fix E1 error on my Whirlpool washer?
E1 – water inlet alarm
- Check that the water faucets are not closed.
- Check that the water pressure in the house is over 20 kPa.
- Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement.
- Check that the drain hose is not below 27½” (700 mm) from the floor.
How do I fix E1 error on my washing machine?
If the error code E1 appears, there is a problem draining the water. First, check the washing machine’s filter. Place a bucket under the rubber pipe and then remove the plug. While it’s draining, remove the filter and rinse it under the faucet.
