Problem with the overflow contact.
- Disconnect power to the washer.
- Turn off both hot and cold water faucets.
- Make sure the drain hose is free from kinks and obstructions.
- Clean the drain pump filter.
- Plugin the washer.
- Try to restart the machine.
Likewise, What does it mean when my Maytag washer says F21?
What is an F21 or F02 Error Code on my Maytag Front Load Washer? These error codes indicate that drain times are longer than expected.
Also, How do I reset my Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
Moreover, Why is my Maytag washer not working?
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.
What does F mean on my Maytag washer?
Maytag F/02 – Drain Cycle Too Long
The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. … If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
Can you reset a Maytag washer?
In addition to a number of heat and tumbling settings, many Maytag washers also have digital displays that indicate the minutes left on a washing cycle, which settings you have chosen and error messages. … You also can reset the washer if you want to cancel a setting you chose.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does F5 mean on my washing machine?
The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
Does a washing machine have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
What does the code F20 mean on a Whirlpool washer?
An F20 or FH error code indicates a water supply problem. Here are some common issues: Both hot and cold water must be connected and turned on. Water inlet hoses kinked. Water inlet valve screen clogged.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load Washer
Error Code | Error |
---|---|
Sud or Sd | There are too many suds in the washing machine. |
F5 E2 | The door is not locking properly. |
F7 E1 | Indicates a motor speed sensing error, |
F8 E1 or LO FL | The washer is sensing a low flow of water. |
• 15 juin 2020
Is there a recall on Maytag washers?
Important: CPSC Recall Remedy Notice Due to COVID-19
Description: The recall involves white Maytag front-load washers with model number MAH9700 and a serial number from 10188468GA through 11683946GJ. The model and serial numbers are located inside the door opening and below the rubber boot.
How do I reset my front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
What does FH error code mean?
FH Error Code
FH indicates that there is a Water Inlet Problem—no or insufficient water supply. Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
Why is my Whirlpool washer stuck on sensing?
A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.
Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I manually drain my Whirlpool washer?
Find the “Pause/Cancel” button on the control panel. Press this button twice to drain the washer. Press the “Power” button and rotate the cycle selection knob to “Drain and Spin” to remove the remaining water from the load. Check the washer’s discharge hose if the water fails to drain from the washtub.
What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
What does F5 mean on Whirlpool?
The F5 on most Whirlpool ranges will indicate that you have a problem with the oven door latch assembly or the oven door switch. Since you are seeing this error code when you are trying to set the self cleaning mode, this is likely the problem with your range. You could have a problem with the door switch.
What does F05 mean?
F05 — Waste pipe blockage or pump issue. Issue: Washing Machines door will not open / the door can be opened but water remains inside the drum.