What is an F21 or F02 Error Code on my Maytag Front Load Washer? These error codes indicate that drain times are longer than expected .
…
Removing the Error
Table of Contents
READ ALSO
- Unplug the washer or disconnect the power for one minute.
- Plug in the washer or reconnect the power.
- Re-select the cycle and press Start.
Likewise, How do you fix F21 codes?
Clogged drain into the sewer
Lint, scraps of paper, small coins, socks – anything can block the drain at the junction of the hose and the sewer hole. The solution is to disconnect the pipe and clean the drain from foreign debris that prevents water from escaping, causing the F21 error code.
Also, What does F21 mean on a Maytag 3000 washer?
In this particular case, error code F21 indicates an issue with your Maytag washing machine’s drain valve. When it takes eight or more minutes for a Maytag washing machine to drain, the device will tell its pipes to close, and you’ll be forced to troubleshoot.
Moreover, How do I clear the error code on my Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I reset my Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
What does error code F20 mean on a Whirlpool Duet washer?
An F20 or FH error code indicates a water supply problem. Here are some common issues: Both hot and cold water must be connected and turned on. Water inlet hoses kinked. Water inlet valve screen clogged.
How do you reset a Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does F mean on my Maytag washer?
Maytag F/02 – Drain Cycle Too Long
The manufacturer has assigned this error or fault code to indicate that the washing machine drain cycle is taking too long. After 8 minutes of drain time the error code is displayed. … If the error code returns, check to be sure the drain hose isn’t clogged or kinked.
What is wrong with my Maytag washer?
Some common Maytag front-load washer problems include not agitating or spinning, and not draining or filling with water. Perhaps your washing machine is vibrating during spin cycles or making noises during wash cycles. … Look, Maytag is a great brand, but if the washer isn’t working that doesn’t work for anybody.
Why is my Maytag washer not working?
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.
Why does my Maytag washer not start?
If your Maytag washing machine isn’t starting, verify that the power cord is connected to a live outlet. Test the outlet with another three-prong appliance. … Select a wash setting and pull out the knob to start the cycle. If it still won’t start, reset the circuit breaker or change out the fuses if they are blown.
What does F5 mean on a washer?
A temperature sensor resistance that is out of the normal range is detected by the Central Control Unit. A failed NTC temperature sensor is what causes the F5 error.
What does F5 mean on washing machine?
The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Why is my washer stuck on sensing?
When Kenmore HE Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, most likely one of these 3 parts malfunction: Failed Water Inlet Valve or Inlet Valve Tap is in OFF position. Shift Actuator not able to change position, before Wash cycle. Control Board malfunctioned.
Why is my Maytag washer stuck on sensing?
If your Maytag washer’s sensing light is stuck and will not move to the appropriate cycles, this is usually caused by a stuck or keypad. The keypad can occasionally become jammed or, if you have recently replaced a part on the washer, you may have forgotten to recycle the codes, which can lead to a stuck sensor light.
Why does my washer keep saying F20?
F20 Error Code
Whirlpool error code F20 appears when no water is detected entering the machine or if the pressure switch trip is not detected. The pressure switch is the part of the machine that monitors high water pressure. The washing machine automatically cancels the wash cycle during an F20 error.
How do I fix my F20 Whirlpool?
To reset the f20 error code, exclude the program crash of the Whirlpool washer. To do this, de-energize your washing machine for 10-20 minutes, then turn it on back. If the error disappears from the display, the problem is successfully eliminated.
What does F20 mean on a washer?
F20 Error Code
F20 indicates a water inlet problem—no water or insufficient water supply. Try the following method to resolve: Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Can you reset a Maytag washer?
In addition to a number of heat and tumbling settings, many Maytag washers also have digital displays that indicate the minutes left on a washing cycle, which settings you have chosen and error messages. … You also can reset the washer if you want to cancel a setting you chose.
Does Whirlpool washer have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Why is my Whirlpool front load washer not draining?
You need to make sure that the drain hose is not kinked at all. Straighten the hose to make sure that there is enough water flow and that you also remove any blockages from the drainpipe well. Ensure that you are using a U-shaped drain and secure it properly. Your instruction manual will show you how to do this.
What does the code F20 mean on a Whirlpool washer?
An F20 or FH error code indicates a water supply problem. Here are some common issues: Both hot and cold water must be connected and turned on. Water inlet hoses kinked. Water inlet valve screen clogged.
Is there a recall on Maytag washers?
Important: CPSC Recall Remedy Notice Due to COVID-19
Description: The recall involves white Maytag front-load washers with model number MAH9700 and a serial number from 10188468GA through 11683946GJ. The model and serial numbers are located inside the door opening and below the rubber boot.
What does FH error code mean?
FH Error Code
FH indicates that there is a Water Inlet Problem—no or insufficient water supply. Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
