Problem with the overflow contact.
- Disconnect power to the washer.
- Turn off both hot and cold water faucets.
- Make sure the drain hose is free from kinks and obstructions.
- Clean the drain pump filter.
- Plugin the washer.
- Try to restart the machine.
Likewise, What does it mean when my Maytag washer says F21?
What is an F21 or F02 Error Code on my Maytag Front Load Washer? These error codes indicate that drain times are longer than expected.
Also, How do I clear the error code on my Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Moreover, How do I reset my Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
Why is my Maytag washer not working?
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.
Can you reset a Maytag washer?
In addition to a number of heat and tumbling settings, many Maytag washers also have digital displays that indicate the minutes left on a washing cycle, which settings you have chosen and error messages. … You also can reset the washer if you want to cancel a setting you chose.
What does F5 mean on a washer?
A temperature sensor resistance that is out of the normal range is detected by the Central Control Unit. A failed NTC temperature sensor is what causes the F5 error.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load Washer
| Error Code | Error |
|---|---|
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
| F8 E1 or LO FL | The washer is sensing a low flow of water. |
• 15 juin 2020
What does F5 mean on washing machine?
The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Why is my washer stuck on sensing?
When Kenmore HE Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, most likely one of these 3 parts malfunction: Failed Water Inlet Valve or Inlet Valve Tap is in OFF position. Shift Actuator not able to change position, before Wash cycle. Control Board malfunctioned.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Does a washing machine have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
Why is my washer not working?
1 Be sure the machine is plugged in and turned on. If necessary, check the receptacle it’s plugged into for power, using a working lamp, appliance, or voltage tester. Be sure the washer lid is closed completely. 2 If the receptacle seems dead, check the circuit breaker or the fuse that serves it.
How do I know if my washing machine control board is bad?
A failed front-load washing machine control board has several symptoms, including the washer not starting, filling, spinning or draining.
How do I reset my front load washer?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
How do I fix F5 error on washing machine?
Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.
What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
What is the problem with Whirlpool washing machines?
The machines, branded as Hotpoint or Indesit, were sold for more than five years, but their door locking system can overheat creating the risk of fire. Owners face the prospect of doing without hot washes for months until products are fixed or replaced.
How do you reset a Whirlpool front load washer?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does F5 and E3 mean on a washing machine?
The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
Why is my Whirlpool washer stuck on sensing?
A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.
