What is an F21 or F02 Error Code on my Maytag Front Load Washer? These error codes indicate that drain times are longer than expected .
…
Removing the Error
- Unplug the washer or disconnect the power for one minute.
- Plug in the washer or reconnect the power.
- Re-select the cycle and press Start.
Likewise, How do you reset a Whirlpool washing machine?
The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Also, How do I clear the error code on my Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
Moreover, How do I reset my Maytag washer?
How to Reset a Maytag Washer
- Press the “Power/Cancel” button.
- Push the appropriate button to choose a new cycle.
- Press “Start/Pause.” You have now reset your Maytag washer.
Why is my Maytag washer not working?
When your washer isn’t working right, the solution may be as simple as switching up detergents, tightening a hose or leveling the appliance. … If you have a front load washer, a dirty drain pump filter can be a common cause of the issues listed below, like problems draining, spinning and odor.
Do Whirlpool washers have a reset button?
How to Confirm You Have Reset Your Whirlpool Washing Machine. … Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
What does F5 mean on washing machine?
The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.
What does F5 mean on a washer?
A temperature sensor resistance that is out of the normal range is detected by the Central Control Unit. A failed NTC temperature sensor is what causes the F5 error.
How do you fix a Maytag washer that won’t drain?
If the washer won’t drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.
Why is my Maytag washer stuck on sensing?
If your Maytag washer’s sensing light is stuck and will not move to the appropriate cycles, this is usually caused by a stuck or keypad. The keypad can occasionally become jammed or, if you have recently replaced a part on the washer, you may have forgotten to recycle the codes, which can lead to a stuck sensor light.
Does a washing machine have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
Why is my washer not working?
1 Be sure the machine is plugged in and turned on. If necessary, check the receptacle it’s plugged into for power, using a working lamp, appliance, or voltage tester. Be sure the washer lid is closed completely. 2 If the receptacle seems dead, check the circuit breaker or the fuse that serves it.
How do you reset a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
Where is the reset button on Whirlpool washing machine?
Is there a reset button on a Whirlpool washer? Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds.
Why is my Whirlpool washer not working?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Why will my Whirlpool washer not start?
First ensure that power is getting to the electrical outlet. If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. … To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
Does unplugging a washer reset it?
On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.
How do you reset a front loader washing machine?
How to reset the washing machine:
- Press POWER to turn the washer off.
- Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
- With the power disabled, press and hold the START/PAUSE button for 5 seconds.
- Plug the washer back in, or turn the circuit breaker back on.
Why is my Whirlpool washer stuck on sensing?
A blinking sensing light indicates an underlying issue with the drain, spin, or any other function. There are several such problems that Whirlpool washers commonly run into. … The washer will function only when the lid/door is completely closed. The water pump belt in the washer has worn out or is damaged.
What is F5 error code?
An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.
What does F5 and E3 mean on a washing machine?
The F5 E3 alert indicates there is issue with the lid lock. … Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. If this is unsuccessful, reboot the machine by unplugging the washer and wait two minutes before plugging the machine back in.
How do I fix F5 error on washing machine?
Remove any objects from the lid and clear any obstructions. Touch POWER to exit cycle, then touch POWER again to release lid. To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.