F9 – Oven Door Lock Failure – Check door lock switches and wiring. Check for stuck lock switch. FH – Detects No Water Entering Machine or No Pressure Switch Trip – Select ‘cancel’ twice to clear this code. If there is NO water in the unit, make sure the valves are turned on all the way.
similarly, Why does my oven say F9?
An F9 error code on a General Electric (GE) oven indicates that the oven’s electronic control system has detected a problem with the automatic door lock. … The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself.
on the other hand, How do I clear F9 code?
How to Remove the F9 Code From Maytag
- Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. …
- Open the oven door and check the door latch. …
- Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. …
- Press the oven door shut gently. …
- Test the oven.
also, How do you reset a Whirlpool stove? Reset power to the product:
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Start a bake cycle.
- Monitor the oven for one (1) minute to ensure the error code does not display again.
- Verify oven operation.
How do I fix F9 heat error?
Sometimes, the F9 error code is the result of an electrical fault that has magnetized the circuitry. Resetting the oven by disconnecting the power for five minutes will demagnetize the circuitry and resolve the F9 error.
How do you fix oven error F9?
The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.
How do you clear code on F9 oven?
How to Remove the F9 Code From Maytag
- Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. …
- Open the oven door and check the door latch. …
- Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. …
- Press the oven door shut gently. …
- Test the oven.
How do I reset my F9 Whirlpool stove?
Reset the appliance
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
Why does stove say f9e0?
This code will most often indicate that the appliance is wired incorrectly at the home electrical supply, or at the hard wire connection. If your oven was installed recently (within approximately 3 months), contact a qualified electrician to verify the electrical supply.
How do I reset my oven door lock?
If the door does not unlatch and you do not have food in the oven, set the oven to Self-Clean for 1-2 hours. Wait approximately 30 minutes for the oven to cool and try to unlock the door. If the door unlocks, the control has reset itself and there should not be any other problems. Do not force the latch at anytime.
What does F9 mean on a Maytag gas stove?
Maytag , Ranges , Appliances. The F9 error code indicates a problem with the oven door lock assembly. The door lock assembly will need to be checked and replaced if defective. If the door lock assembly is okay, then the electronic oven control board will need to be replaced.
Do Whirlpool ovens have a reset button?
You reset an Accubake oven by hitting the cancel slash off button, waiting a minute or more for power to dissipate, then turning it back on. That’s a lot less inconvenient than turning it off at the breaker.
Do Whirlpool microwaves have a reset button?
Press the “Off/Clear’ button to cancel anything on the display, and reset the microwave. This is a soft reset and will simply get you out of any program you have started. Press it when the cooking complete reminder appears on the display, for example, and the “Your Food is Ready” message will disappear.
What is f2e1 error code?
F2-E1 – Touch Pad Cable Unplugged – Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the ‘cancel’ function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly.
Where is the oven door switch?
The door switch is a small cylindrical part set into the upper right or left corner of the oven door aperture with wires through the back.
What does F9 mean on a Maytag stove?
The F9 error code indicates a problem with the oven door lock assembly. The door lock assembly will need to be checked and replaced if defective. If the door lock assembly is okay, then the electronic oven control board will need to be replaced.
What causes an oven to stop heating?
The Oven Won’t Heat
An oven that won’t heat is usually the result of a faulty igniter (for a gas oven) or heating element (for an electric oven). If both your gas oven and your gas burners have stopped working, the problem is most likely with the gas line, and will require professional repair.
How do I fix the F9 code on my Frigidaire oven?
Turn off your oven and then unplug it. Wait several minutes before you plug the appliance in once again and turn it on. This should reset the system and prompt you to reprogram the electronic control panel.
Why is my Whirlpool oven not working?
An electric oven not heating up can often be attributed to a defective bake element. This Whirlpool oven heating element is a metal coil located at the bottom of electric ovens. When you turn on the oven, wires inside the coil receive electrical current that heats the metal, providing the heat you need to cook food.
How do I fix F9E0?
F9E0:
- Press CANCEL>CANCEL>START to enter the Diagnostics Mode and verify the failure. …
- Unplug range or disconnect power.
- Verify that the house power supply provides 240 VAC between L1 and L2, and 120 VAC between L1 and N and L2 and N. …
- Verify that the electric supply is wired correctly at the range terminal block.
How do I reset my F9E0 Whirlpool oven?
Reset the appliance
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Monitor the range or oven for one (1) minute to ensure the error code does not display again.
- Verify the range or oven operation.
What does F8E0 mean on oven?
0. Hello. F8E0 is a Cooling Fan Speed Too Low Fan speed below 500 rpm, either because the fan is. spinning too slowly or because there is a problem with the Hall Effect sensor.
Why does my oven says door locked?
You can diagnose the failure simply by disconnecting the wires from the micro-switch and then see if the oven will operate in bake or broil. If it does, replace the latch assembly. If it continues to display “unlock door”, the electronic oven control will need to be replaced.
Why does my oven door not close?
If your oven door doesn’t close all the way or hangs unevenly, several issues could be the culprit. … Replace the hinges with identical new ones and hook them back into the hinge holes in the oven. Push the door down to lock the hinges in place, or replace the screws. Check the door springs to see if they are broken.
Don’t forget to share the post !