- Locate the drain-access filter panel on the bottom of the drawer.
- Remove the rack that sits above it.
- Pull up to lift the drain filter and remove it from the machine.
- Set the filter under the faucet to rinse it clean with cold water.
- Reinstall the filter and confirm that it sits flush with the bottom of the DishDrawer.
similarly, What does F1 mean on a Westinghouse dishwasher?
An F1 error code on your Westinghouse dishwasher indicates that a leak is detected somewhere in the unit, whereas an F3 error code pinpoints the issue to a problem with the overflow protector. The overflow protector is normally located in the front left corner of the dishwasher tub.
on the other hand, Why is my Dishdrawer not draining?
Disconnect the drain hose at both connection points. … Stagnant water may be trapped in the hose, so remove it carefully and pour any trapped water down the sink. Straighten the hose and look through it. If you can see obstructions, the drain hose is likely the cause of your drainage problems.
also, What does F9 mean on a dishwasher? A water pressure sensor is related to the F9 fault code on Glow-Worm boilers.
Where is the flood switch on a dishwasher?
The anti flood switch is in the bottom of the bas of the dishwasher. If its activated try and pull the dishwasher out and tip it 45 degs backwards and the water should drain out from the base and that way the flood switch will reset itself.
How do I fix F5 error on dishwasher?
– Also if you add water softener in inlet of water, water pressure might go down and cause issue with F5 error. The solution is to remove one filter from inlet pipe (given by IFB) The inlet pipe has filter at both ends, and it becomes too many filter once water softener is added in between, Outlet: – This is hilarious.
How do I fix the F3 error on my dishwasher?
It there is the F3 fault code on the display, there must be a leak in the bottom section of your dishwasher. When the base tray is full, the system activates the flood switch and shows the code. Pull out the dishwasher and tilt it backwards until the water drains completely. Use a tray or bucket.
How do I reset my DishDrawer?
Reset Procedures for the Fisher & Paykel Dishwasher
- Press and hold the button decorated with the key and lock image for five seconds.
- Press the power button to turn off power to the Fisher & Paykel dishwasher.
- Wait a few minutes and then press the power button to restore power.
How do I unlock my DishDrawer?
Unlock by powering your DishDrawer™ back on (unless Keylock is activated, see above). Press any button and open drawer within 30 seconds.
How do I fix error e1 F9 on Maytag washer?
Possible Solutions
Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub. Do not tape over drain opening. Also make sure that the drain hose end is higher than 36 inches from the floor.
What does f2 mean on sharp dishwasher?
This error message means that you have a leak under the floor pan. Please check the machine for leaks. At the bottom there is a float switch that triggers the Aqua stop in the event of a leak. Either you have to open the rectangular cover below the door to check.
How do I clear the error code on my KitchenAid dishwasher?
Control Panel Reset
When powering down the unit and turning it back on doesn’t work, it may be best to reset the control panel’s computer. This is done by pressing two buttons, one after the other, at least five times each for a total of 10 presses. The door must be completely shut while the buttons are being pressed.
What does eo1 mean on a Beko dishwasher?
If the e01) error means the water isn’t flowing into the dishwasher fast enough, you should shut the dishwasher off for 5 minutes and replace the valve if the water pressure is good.
Where is the flood switch on a Beko dishwasher?
Our online tools are here 24 hours a day to help you arrange the service you need. The flood switch at the base of the dishwasher cabinet has activated.
What are the most common problems with dishwashers?
Here are the five most common problems with dishwashers (and how to fix them).
- #1 Problem: Dishes not drying. …
- #2 Problem: Dishwasher not draining. …
- #3 Problem: Dishwasher leaves spots or a film on glassware. …
- #4 Problem: Dishwasher running too long. …
- #5 Problem: Crumbs and food on dishes.
What does F5 mean on sharp dishwasher?
The F5 code means that the machine is not draining. Either there is something blocking the drain line or the drain pump is defective.
What is divisor position error in dishwasher?
F9 is a divisor position error on your Kenwood dishwasher caused due to the flow meter of the dishwasher. Please unplug the dishwasher and pull it out then tip it backwards so excess water drains out from the back of the unit.
What is F2 in dishwasher?
The F2 code means that water level exceeds the admissible one. This may be due to a blocked or faulty drain pump and/or inlet valve. This is a common problem, because food particles often get stuck in the drain system and prevent dishwashers from draining properly.
How do you drain a dishwasher?
How to Drain Your Dishwasher
- Step 1: Prepare Your Dishwasher. …
- Step 2: Make Sure Your Dishwasher is Turned Off. …
- Step 3: Remove the Stagnant Water With a Towel. …
- Step 4: Perform a Check On the Drain Hose. …
- Step 5: Remove Drain Hose and Clean. …
- Step 6: Check Dishwasher Drain.
How do I find the error code on my Whirlpool dishwasher?
Some Whirlpool dishwashers display an error code by flashing the clean Light on the display in a pattern. If your Whirlpool dishwasher does NOT have a digital display, the clean Light will flash the function code then the clean Light will pause for 2 seconds and then will flash the problem code.
How do you run a diagnostic on a Fisher Paykel dishwasher?
Diagnostic Mode. With Power off, press/hold Keylock, then press Start/Pause at the same time for 5 seconds. Release the buttons when it powers-on. Press Power once.
Why does my Fisher and Paykel dishwasher beep?
First and foremost, check the hose of your dishwasher. If it is bent or broken, it may not be draining the water which results in activating the beeps. To fix it, if there is bent, you may be able to replace it yourself and if it is broken, you need to replace it with new one.
What does E5 mean on a dishwasher?
Fisher and Paykel Dishwasher Dishdrawer Error Code E5 is the first three program indicator lights flashing. There is a water supply hose that is bent or crimped. The drain hose is not high.
Don’t forget to share the post !