You can fix this by doing the following:
- Select MENU on your remote control.
- Select Settings.
- Select Satellite.
- Select Repeat Satellite Setup.
- Select the DASH button on your remote control.
- Select Dish Type. …
- Select Continue.
- Please wait a few minutes for your receiver to verify the new dish configuration.
Likewise, What’s wrong with DIRECTV satellite?
The broadcaster has told the FCC that the satellite has a major battery thermal problem with its on-board satellite. The filing was made on January 19th with the satellite’s manufacturer Boeing saying that the batteries damaged cells cannot be isolated and may burst if a recharge is attempted.
Also, What does code 775 on DIRECTV mean?
You’ll see DIRECTV error code 775 when the signal between your receiver and satellite dish is interrupted. Check your receiver connections to resolve this issue.
Moreover, Why does my DIRECTV say to be announced?
The “To Be Announced” message on your guide indicates that no programming information is being provided by the broadcaster or your cable box has not downloaded the programming information for that date/time. This commonly happens after a power outage or after you have reset your cable box by unplugging the power cable.
Why do I keep losing my satellite signal?
This issue is usually a result of the satellite dish being in a slightly wrong position, damaged or malfunctioning equipment, severe weather, or something blocking the dish’s view of the sky. Your signal strength can affect the delivery of your live programming, though with a DVR you can still access recorded content.
Why is my DirecTV screen black?
Problem with Cable connection – Your Directv is most likely to experience a black screen issue due to a cable connection problem. For instance, damaged cables, loose connections, inactive power source. … For instance, your DirecTV might be mistakenly set on a wrong input. To avoid this, make sure it’s on the right input.
How do you reset a DIRECTV satellite dish?
Press the reset button
- Locate the reset button. On most DIRECTV receivers, there is a small red button located inside the access card door. With others, the button is on the side of the receiver.
- Press the red button, then wait for your receiver to reboot.
How do I fix SWM connection loss on DIRECTV?
Unplug the Swim power inserter from the power outlet. Wait for 30 seconds. Plug the Swim power inserter back into its power outlet, and make sure it’s turned on and working. Make sure everything’s hooked up, turn your TV on and check to see if the issue has been resolved.
How do I reboot my DIRECTV receiver?
Unplug your receiver
- Unplug your receiver’s power cord from the electrical outlet, wait 15 seconds, and plug it back in.
- Press the Power button on the front panel of your receiver. Wait for your receiver to reboot.
How do I fix my DIRECTV remote not working?
Receiver and remote control reset
If the buttons on your remote are not responding, try resetting the receiver and remote control. On most DIRECTV receivers, there is a red button on the side of the receiver or inside the access card door. Press and hold the red button until the receiver restarts.
Why can’t I see my guide on DIRECTV?
If the guide still didn’t come up, applying a hard reset might be the best action to take. To do this, you need to unplug all connected cable and wait for at least 60 seconds, then plug it back in.
Why is my satellite receiver not working?
To reset your receiver: Unplug the receiver’s power cord from the back of the receiver or from the wall outlet. Leave unplugged for 30 seconds and plug back in. The receiver should boot up properly in less than 90 seconds.
Can I spray Pam on my satellite dish?
Non-stick cooking and waterproofing sprays such as PAM or Rain-X are not recommended for keeping snow and ice off your satellite dish. … Furthermore, these chemicals could damage the surface of the dish. A good rule of thumb is if you wouldn’t spray your TV screen with it, don’t spray your dish with it either.
How do I fix my satellite signal?
Satellite reception problems
- Cables. Check all the cables between your TV equipment and satellite dish are connected securely. …
- Reboot. Unplug your receiver from the mains and leave for 10 minutes. …
- Dish has moved. …
- Dish Installation. …
- Obstructions. …
- Heavy Rain. …
- Snow.
How do I fix my black screen on DIRECTV?
Solutions
- Turn TV off and on.
- Turn DIRECTV Receiver off and on.
- Make sure light on front panel of receiver is lit.
- Press the “TV/DSS” button on the remote control or front panel of the receiver (not all receivers have this option).
- Reset the receiver by unplugging the power cord for 15 seconds.
How do I fix my TV when the screen goes black?
Unplug the TV from the wall, and, if possible, remove the power cord from the back of the TV to perform a soft reset. Wait 30 seconds, and plug the TV back into a working outlet to test it again.
How do I reset my DIRECTV remote control?
If that didn’t help, try resetting the remote to its default factory settings:
- Press and hold MUTE and SELECT together until the light flashes three times.
- Press 9, 8, 1 and SELECT. The remote flashes four times and should now reset.
Can I adjust my DIRECTV dish myself?
Even if you didn’t install the dish yourself, realigning your satellite dish is a fairly easy process. Once you have the coordinates for your location, it’s just a matter of making minor adjustments until the signal strength is strong. Use the buttons on your receiver or the remote to access the Direct TV Menu.
How do I refresh my satellite receiver?
How to reset your receiver
- Unplug the power cord from the back of the receiver.
- Leave it unplugged for 30 seconds, then plug it back in.
- The receiver should boot up properly in less than 90 seconds, with lights flashing in front.
How do I reset my DIRECTV remote control?
To reset DIRECTV remotes to their default factory settings, press and hold the MUTE and SELECT buttons until the remote’s light flashes three times. Then, enter 981 and press SELECT. The remote will flash four times to let you know it has been reset.
How do I connect my DIRECTV SWM?
DIRECTV specs suggest connecting the power inserter one of three ways. On SWM-enabled dishes, a single line is run to a splitter. A cable is run from the red connection on the splitter into the “Power to SWM” connection on the power inserter. Then, a cable is run from the “Signal to IRD” connection to your receiver.
What is SWiM DIRECTV?
SWiM stands for Single Wire Multiswitch, and it’s a proven technology from DIRECTV that was first rolled out to customers in 2007. … If you just have a dish with no multiswitch, there are SWM-equipped dishes that run one wire out instead of four. The addition of a splitter can give you as many lines as you need.
What is error code 721 on DIRECTV?
Check package and refresh service
You get a 721 error code if: The channel you‘re trying to watch isn’t included in your subscription package. Your receiver isn’t getting the program info for this channel.